Eşyalarını Tamir Et Topluluk Mağaza

Game Boy Outer Case Replacement

Salt Önkoşul
Bu kılavuz yalnızca diğer kılavuzlar için bir ön koşul olarak kullanılmak üzere tasarlanmıştır. Tek başına eksiktir.

Giriş

This guide explains how to remove the outer case so that you can access the internal components of the Game Boy. This will be helpful for other guides related to this hand-held gaming console.

Neye ihtiyacın var

  1. Game Boy Outer Case Replacement, Batteries: adım 1, 2 resimden 1. Game Boy Outer Case Replacement, Batteries: adım 1, 2 resimden 2.

    • Switch your Game Boy off and remove the cartridge.

    Düzenle

  2. Game Boy Outer Case Replacement: adım 2, 3 resimden 1. Game Boy Outer Case Replacement: adım 2, 3 resimden 2. Game Boy Outer Case Replacement: adım 2, 3 resimden 3.

    • Use a fingernail (or small coin) to push down on the battery door latch and remove the battery door.

    • The release latch is a plastic spring clip. If your Game Boy is getting on in years, be careful as the plastic may be brittle.

    • When you're replacing the cover, be sure to get its two plastic tabs into the slots in the bottom of the battery compartment before pushing the cover back in place.

    Düzenle

  3. Game Boy Outer Case Replacement: adım 3, 2 resimden 1. Game Boy Outer Case Replacement: adım 3, 2 resimden 2.

    • Use a fingernail to pry each battery outward from the positive (+) terminal to remove them.

    • Dispose of used batteries properly!

    • Remove the batteries from your Game Boy before storing it for more than a month or so.

    Düzenle

  5. Game Boy Outer Case Replacement, Outer Case: adım 4, 1 resimden 1.

    • Remove the six Triwing screws from the back of the device.

    Düzenle

  6. Game Boy Outer Case Replacement: adım 5, 1 resimden 1.

    • Gently separate the device's front casing from the back casing after you remove the screws.

    • Be careful not to completely separate the casing halves, as they are still joined by a large ribbon cable that may be damaged.

    Düzenle

  7. Game Boy Outer Case Replacement: adım 6, 1 resimden 1.

    • Slide the front side of the casing down to expose the ribbon cable connector.

    Düzenle

  8. Game Boy Outer Case Replacement: adım 7, 1 resimden 1.

    • Grip the ribbon connector with your thumb and forefinger. Pull down gently until the connector, not the ribbon itself, comes out of its socket.

    • Separate the front and back casings.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

13 farklı kişi bu kılavuzu tamamladı.

Yazar

21 tane daha katılımcı ile

Andrew Tramposch

Üyelik tarihi: 06/24/10

2.243 İtibar

6 adet Kılavuz yazıldı

Rozetler: 17

+14 tane daha rozet

Ekip

Cal Poly, Team 3-2, Johann Summer 2010 Cal Poly, Team 3-2, Johann Summer 2010 üyesi

CPSU-JOHANN-R10S3G2

3 Üyeler

34 adet Kılavuz yazıldı

2 Yorum

U need a tri-wing screwdriver not a Philips #00

radiofreeroyaloak - Yanıt

It is a Philips if gb was made after 1998 or so.

Sam - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 2

Her zaman: 15,686