Ana içeriğe geç

Giriş

Replace a broken screen in your Gateway SA1 laptop.

  1. Gateway SA1 Screen Replacement, Battery: adım 1, 1 resimden 1.
    • Move the latch to the right of the battery to unlock.

  2. Gateway SA1 Screen Replacement: adım 2, 1 resimden 1.
    • Slide the latch on the left directly below the battery to unlock and pull out the battery as shown.

    • The latch must be held in position to remove the battery.

  3. Gateway SA1 Screen Replacement, Screen: adım 3, 2 resimden 1. Gateway SA1 Screen Replacement, Screen: adım 3, 2 resimden 2.
    • Remove the hinge covers by lifting each with the sharp point of the spudger.

    • Notice that the middle cover has a different shape and is more difficult to remove.

  4. Gateway SA1 Screen Replacement: adım 4, 2 resimden 1. Gateway SA1 Screen Replacement: adım 4, 2 resimden 2.
    • Remove the six screw covers on the front bezel with the sharp point of the spudger.

    • The bottom two are more difficult to remove.

  5. Gateway SA1 Screen Replacement: adım 5, 1 resimden 1.
    • Remove the six 5.9 mm Philips screws securing the screen bezel.

  6. Gateway SA1 Screen Replacement: adım 6, 3 resimden 1. Gateway SA1 Screen Replacement: adım 6, 3 resimden 2. Gateway SA1 Screen Replacement: adım 6, 3 resimden 3.
    • Remove the front bezel by prying it off with the wedged end of the spudger.

    • Verify that your spudger does not touch the LCD.

    • The screen inverter is now exposed below the LCD.

  7. Gateway SA1 Screen Replacement: adım 7, 1 resimden 1.
    • Remove the single 3.8mm Phillips screw mounting the screen inverter to the computer.

  8. Gateway SA1 Screen Replacement: adım 8, 2 resimden 1. Gateway SA1 Screen Replacement: adım 8, 2 resimden 2.
    • Use your finger, or the spudger, to pry the inverter board out.

    • This exposes the wires behind it.

  9. Gateway SA1 Screen Replacement: adım 9, 1 resimden 1.
    • Unplug the LCD back light cables from the right side of the screen inverter.

  10. Gateway SA1 Screen Replacement: adım 10, 2 resimden 1. Gateway SA1 Screen Replacement: adım 10, 2 resimden 2.
    • Remove the six screws that mount the screen to the hinge mounts.

    • Two 2.5 mm Phillips screws.

    • Four 3.8 mm Phillips screws.

  11. Gateway SA1 Screen Replacement: adım 11, 1 resimden 1.
    • Unplug the cable from the webcam board.

    • Be gentle, do not use excessive force or you may break the connection.

  12. Gateway SA1 Screen Replacement: adım 12, 1 resimden 1.
    • Separate the screen from the display cover.

    • Do not touch the back of the screen.

  13. Gateway SA1 Screen Replacement: adım 13, 2 resimden 1. Gateway SA1 Screen Replacement: adım 13, 2 resimden 2.
    • Remove the three tape strips that hold down the cables.

    • Be careful not to tear any of the tape. The piece holding down the webcam wires is especially delicate.

  14. Gateway SA1 Screen Replacement: adım 14, 2 resimden 1. Gateway SA1 Screen Replacement: adım 14, 2 resimden 2.
    • Unplug the display data cable from the screen connector.

    • This connection is very fragile; do not use excessive force.

    • The screen should now be free from all wire connections.

  15. Gateway SA1 Screen Replacement: adım 15, 1 resimden 1.
    • Remove the four 2.8 mm Phillips screws that secure the screen to the mounting bracket using a screwdriver.

    • There will be two screws on either side of the mounting bracket.

  16. Gateway SA1 Screen Replacement: adım 16, 1 resimden 1.
    • You can now remove and replace the screen.

Sonuç

To reassemble your device, follow these instructions in reverse order.

2 farklı kişi bu kılavuzu tamamladı.

Diego Carteno

Üyelik tarihi: 15-04-2010

258 İtibar

7 adet Kılavuz yazıldı

Takım

Cal Poly, Team 24-20, Regan Spring 2010 Cal Poly, Team 24-20, Regan Spring 2010 üyesi

CPSU-REGAN-S10S24G20

4 Üyeler

14 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 2

Son 30 gün: 7

Her zaman: 18,628