Eşyalarını Tamir Et Topluluk Mağaza

GoPro Hero 3 Silver Expansion Port Replacement

Neye ihtiyacın var

  1. GoPro Hero 3 Silver Expansion Port Replacement, Battery: adım 1, 2 resimden 1. GoPro Hero 3 Silver Expansion Port Replacement, Battery: adım 1, 2 resimden 2.

    • Pull back on the tab on the back of GoPro to open the battery cover.

    Düzenle

  2. GoPro Hero 3 Silver Expansion Port Replacement: adım 2, 1 resimden 1.

    • Pull the battery out using the tab.

    Düzenle

  3. GoPro Hero 3 Silver Expansion Port Replacement, Expansion Port: adım 3, 2 resimden 1. GoPro Hero 3 Silver Expansion Port Replacement, Expansion Port: adım 3, 2 resimden 2.

    • Use the plastic opening tool to remove the faceplate.

    • There is some adhesive and clips so be careful and the faceplate should pop right off.

    Düzenle

  5. GoPro Hero 3 Silver Expansion Port Replacement: adım 4, 2 resimden 1. GoPro Hero 3 Silver Expansion Port Replacement: adım 4, 2 resimden 2.

    • Now that the faceplate is off, it is time to remove the 4 screws on each corner.

    • Use the T4 tool bit from the iFixit toolkit in order to remove the 4 screws on each corner.

    Düzenle

  6. GoPro Hero 3 Silver Expansion Port Replacement: adım 5, 2 resimden 1. GoPro Hero 3 Silver Expansion Port Replacement: adım 5, 2 resimden 2.

    • Note: Make sure you remove the door cover of the USB, mini HDMI, and SD port before. Separating the motherboard will be easier.

    • Using the plastic opening tool, slowly pry open the motherboard assembly.

    Düzenle

  7. GoPro Hero 3 Silver Expansion Port Replacement: adım 6, 2 resimden 1. GoPro Hero 3 Silver Expansion Port Replacement: adım 6, 2 resimden 2.

    • Use the spudger to gently pry off the connector of the housing to the motherboard.

    • You should now have the motherboard assembly and the housing separated.

    Düzenle

  8. GoPro Hero 3 Silver Expansion Port Replacement: adım 7, 3 resimden 1. GoPro Hero 3 Silver Expansion Port Replacement: adım 7, 3 resimden 2. GoPro Hero 3 Silver Expansion Port Replacement: adım 7, 3 resimden 3.

    • Use the spudger to remove the heat shield tape and detach the image sensor from the motherboard.

    • Using the T4 Torx toolbit, remove the 4 screws that connect the sensor to the lens.

    • Remove the silver connector of the image sensor from the motherboard using the spudger to pry it off.

    Düzenle

  9. GoPro Hero 3 Silver Expansion Port Replacement: adım 8, 2 resimden 1. GoPro Hero 3 Silver Expansion Port Replacement: adım 8, 2 resimden 2.

    • The media adapter is attached to the motherboard via 3 screws:

    • x1 T4 Torx

    • x2 Phillips #00

    • There is a little silver bracket (in the yellow circle) that is held down by the Phillips #00 screw so be careful not to lose it.

    Düzenle

  10. GoPro Hero 3 Silver Expansion Port Replacement: adım 9, 2 resimden 1. GoPro Hero 3 Silver Expansion Port Replacement: adım 9, 2 resimden 2.

    • With a little prying, use the spudger to detach the media adapter's connector from the motherboard.

    • Remove the media adapter from the motherboard.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

2 farklı kişi bu kılavuzu tamamladı.

Yazar

4 tane daha katılımcı ile

Brian Alvarez

Üyelik tarihi: 04/02/15

1.439 İtibar

6 adet Kılavuz yazıldı

Rozetler: 15

+12 tane daha rozet

Ekip

Cal Poly, Team 24-7, Lancaster Spring 2015 Cal Poly, Team 24-7, Lancaster Spring 2015 üyesi

CPSU-LANCASTER-S15S24G7

3 Üyeler

21 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 4

Son 30 gün: 7

Her zaman: 1,844