Eşyalarını Tamir Et Topluluk Mağaza

Graco Secure Coverage LED Nursery Unit Replacement

Giriş

Use this guide to replace the LED on your Graco Secure Coverage Digital Baby Monitor for nursery unit.

The LED replacement includes the LED and battery replacement.

Neye ihtiyacın var

  1. Graco Secure Coverage LED Nursery Unit Replacement, Nursery Unit Battery: adım 1, 3 resimden 1. Graco Secure Coverage LED Nursery Unit Replacement, Nursery Unit Battery: adım 1, 3 resimden 2. Graco Secure Coverage LED Nursery Unit Replacement, Nursery Unit Battery: adım 1, 3 resimden 3.

    • Remove the 9mm screw from the battery cover of the nursery unit using a Phillips #1 tip screwdriver.

    Düzenle

  2. Graco Secure Coverage LED Nursery Unit Replacement: adım 2, 2 resimden 1. Graco Secure Coverage LED Nursery Unit Replacement: adım 2, 2 resimden 2.

    • Using the plastic opening tool, pry and remove the battery cover carefully.

    • Remove the batteries using plastic opening tool.

    • Replace the batteries.

    Düzenle

  4. Graco Secure Coverage LED Nursery Unit Replacement, LED Nursery Unit: adım 3, 2 resimden 1. Graco Secure Coverage LED Nursery Unit Replacement, LED Nursery Unit: adım 3, 2 resimden 2.

    • Remove the two 9mm Phillips #1 screws from the rare case of the device.

    • Place the screws in a secure place.

    Düzenle

  5. Graco Secure Coverage LED Nursery Unit Replacement: adım 4, 1 resimden 1.

    • Hold the bottom of the device with one hand and pull down to separate the front and rare cases.

    • While holding the device with one hand, use plastic opening tool to pry the edges of the front case away from the back case.

    • Apply constant force carefully to avoid breaking any other plastic parts from the device.

    Düzenle

  6. Graco Secure Coverage LED Nursery Unit Replacement: adım 5, 2 resimden 1. Graco Secure Coverage LED Nursery Unit Replacement: adım 5, 2 resimden 2.

    • Remove all three 7mm Phillips #1 screws from the mother board.

    • Place the screws in secure place.

    Düzenle

  7. Graco Secure Coverage LED Nursery Unit Replacement: adım 6, 3 resimden 1. Graco Secure Coverage LED Nursery Unit Replacement: adım 6, 3 resimden 2. Graco Secure Coverage LED Nursery Unit Replacement: adım 6, 3 resimden 3.

    • Flip over the motherboard to look at the LED pins that are connected to it.

    • Solder off the LED pin from the motherboard.

    • There are many pins are connect to the motherboard, so make sure that you solder off the LED pin.

    • Replace the LED.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

2 tane daha katılımcı ile

Bryson Wolff

Üyelik tarihi: 08/31/15

237 İtibar

2 adet Kılavuz yazıldı

Rozetler: 10

+7 tane daha rozet

Ekip

USF Tampa, Team 6-5, Remmell Fall 2015 USF Tampa, Team 6-5, Remmell Fall 2015 üyesi

USFT-REMMELL-F15S6G5

4 Üyeler

8 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 1

Her zaman: 133