Ana içeriğe geç

Graco Secure Coverage LED Parent Unit Replacement

Neye ihtiyacın var

  1. Graco Secure Coverage LED Parent Unit Replacement, Parent Unit Battery: adım 1, 3 resimden 1. Graco Secure Coverage LED Parent Unit Replacement, Parent Unit Battery: adım 1, 3 resimden 2. Graco Secure Coverage LED Parent Unit Replacement, Parent Unit Battery: adım 1, 3 resimden 3.
    • Using plastic opening tool, pry and remove the battery lid.

  2. Graco Secure Coverage LED Parent Unit Replacement: adım 2, 1 resimden 1.
    • Remove the battery by holding the device with one hand and pulling the battery out with other hand carefully.

    • Make sure that you disconnect the battery's wire before you remove the battery.

  3. Graco Secure Coverage LED Parent Unit Replacement, LED Parent Unit: adım 3, 2 resimden 1. Graco Secure Coverage LED Parent Unit Replacement, LED Parent Unit: adım 3, 2 resimden 2.
    • There are two screws on the rare case of the device. For the one shown in blue marker requires either an extended screwdriver or putting on a little pressure on a regular screwdriver.

    • Remove the two 9mm Phillips #1 screws from the rare case of the device.

    • If you cannot remove the screw with low pressure, do not use high pressure to remove it. It may cause a damage on the device case. Use an extended screwdriver instead.

  4. Graco Secure Coverage LED Parent Unit Replacement: adım 4, 2 resimden 1. Graco Secure Coverage LED Parent Unit Replacement: adım 4, 2 resimden 2.
    • Using opening plastic tool, pry the two grey cases from both sides of the device.

    • Take your time and apply constant force to avoid breaking or damaging any other plastic parts.

    • While pry off the grey cases, hold the device with your other hand to remove the cases

  5. Graco Secure Coverage LED Parent Unit Replacement: adım 5, 1 resimden 1.
    • Pry the edges of the device to separate the front and rare cases.

    • While prying the edges, hold the device with one hand to pull out each case a part.

    • Make sure you use a constant force, and the pushbuttons are pried off completely.

  6. Graco Secure Coverage LED Parent Unit Replacement: adım 6, 2 resimden 1. Graco Secure Coverage LED Parent Unit Replacement: adım 6, 2 resimden 2.
    • Remove the 7mm Phillips #1 screw from the mother board.

    • Place the screw in a secure place.

  7. Graco Secure Coverage LED Parent Unit Replacement: adım 7, 2 resimden 1. Graco Secure Coverage LED Parent Unit Replacement: adım 7, 2 resimden 2.
    • Flip over the motherboard.

    • Solder off LED from motherboard.

    • There are many pins attached to the motherboard, make sure you solder off the proper pins that attached to the LED's.

    • Replace the LED's

Sonuç

To reassemble your device, follow these instructions in reverse order.

Bryson Wolff

Üyelik tarihi: 08/31/15

237 İtibar

2 adet Kılavuz yazıldı

Ekip

USF Tampa, Team 6-5, Remmell Fall 2015 USF Tampa, Team 6-5, Remmell Fall 2015 üyesi

USFT-REMMELL-F15S6G5

4 Üyeler

8 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 2

Her zaman: 84