Ana içeriğe geç

Giriş

This guide will teach you how to install a new case on your HP Photosmart 935 camera. If your camera case is cracked or starting to come apart, this guide will help you replace it with a new one.

Parçalar

Hiçbir parça belirtilmedi.

  1. HP Photosmart 935 Plastic Casing Replacement, Batteries: adım 1, 2 resimden 1. HP Photosmart 935 Plastic Casing Replacement, Batteries: adım 1, 2 resimden 2.
    • Flip the camera over so the bottom is facing you.

  2. HP Photosmart 935 Plastic Casing Replacement: adım 2, 2 resimden 1. HP Photosmart 935 Plastic Casing Replacement: adım 2, 2 resimden 2.
    • Slide the bottom cover in the direction of the arrow to open it.

  3. HP Photosmart 935 Plastic Casing Replacement: adım 3, 1 resimden 1.
    • Pull out the batteries.

  4. HP Photosmart 935 Plastic Casing Replacement, Plastic Casing: adım 4, 1 resimden 1.
    • Using a Phillips #00 screwdriver, remove the two 4.70mm screws in the bottom of the plastic casing.

  5. HP Photosmart 935 Plastic Casing Replacement: adım 5, 2 resimden 1. HP Photosmart 935 Plastic Casing Replacement: adım 5, 2 resimden 2.
    • Remove the four 4.70mm screws on the left side of the camera.

  6. HP Photosmart 935 Plastic Casing Replacement: adım 6, 2 resimden 1. HP Photosmart 935 Plastic Casing Replacement: adım 6, 2 resimden 2.
    • Remove the four 4.70mm screws on the opposite side of the camera.

  7. HP Photosmart 935 Plastic Casing Replacement: adım 7, 3 resimden 1. HP Photosmart 935 Plastic Casing Replacement: adım 7, 3 resimden 2. HP Photosmart 935 Plastic Casing Replacement: adım 7, 3 resimden 3.
    • Use your thumbs to pry the case apart.

    • It is easiest to pry the case apart if you start at the bottom.

    • The case should come apart with minimal effort. If it doesn't, you can use a spudger or plastic opening tool to pry it open.

  8. HP Photosmart 935 Plastic Casing Replacement: adım 8, 1 resimden 1.
    • This step requires a significant amount of force.

    • Pull the bottom half of the inner camera out of the case by half an inch. This may be difficult and require some force.

  9. HP Photosmart 935 Plastic Casing Replacement: adım 9, 2 resimden 1. HP Photosmart 935 Plastic Casing Replacement: adım 9, 2 resimden 2.
    • While pulling the camera out of the case, note the small soft plastic cover on the side. This cover will detach from the rest of the device.

    • Once the bottom of the inner camera is pulled out, pull the device out completely.

    • Use a firm grasp when removing the device from the case for stability and control.

Sonuç

To reassemble your device, follow these instructions in reverse order.

Clay Young

Üyelik tarihi: 04-04-2012

227 İtibar

2 adet Kılavuz yazıldı

Takım

Cal Poly, Team 15-13, Forte Spring 2012 Cal Poly, Team 15-13, Forte Spring 2012 üyesi

CPSU-FORTE-S12S15G13

5 Üyeler

10 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 1

Son 30 gün: 3

Her zaman: 1,577