Bu sürüm, hatalı düzenlemeler içerebilir. En son doğrulanmış bellek kopyası dönün.
Neye ihtiyacın var
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Using a Phillips #2 screwdriver, remove the two screws securing the lid on the master brake fluid cylinder.
-
Remove the lid from the master cylinder, and set it aside.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Locate the brake fluid bleed valve on the top of the front brake assembly, and flip up the rubber cap covering it.
-
Slide a 3/8" brake bleeder hose over the bleed valve.
-
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Carefully pump the brake lever a few times to build up pressure in the brake lines.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Using a 3/8" wrench with your left hand, open the bleed valve on the front brake cylinder.
-
The built-up pressure in the lines will force some of the brake fluid out of the lines.
-
Continue to force more brake fluid out of the brake lines by depressing the front brake lever with your right hand.
-
Once the brake lever is completely depressed, quickly close the bleed valve, making sure that no air bubbles enter into the brake lines.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Repeat the process outlined in step five and six until the amount of brake fluid in the master cylinder is getting low.
-
Refill the master cylinder with fresh brake fluid until the level of fluid is even with the metal protrusion in the rear right corner of the master cylinder.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Continue flushing the brake lines as described above until you see the new brake fluid coming through the bleed tube.
-
When you are seeing new brake fluid coming through the bleed hose, stop the flushing process and firmly close the bleed valve.
-
Gently pull the bleed tube off of the bleed valve and re-cover the valve with the little rubber cap.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Fill the master brake cylinder one last time with fresh brake fluid until the fluid is level with the metal tab in the rear right corner of the cylinder.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Using a damp rag, wipe down the rim and rubber gasket of the master cylinder and the master cylinder cover.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Using a Phillips #2 screwdriver, replace the master cylinder cover and screw it firmly into place.
-
İptal et: Bu kılavuzu tamamlamadım.
12 farklı kişi bu kılavuzu tamamladı.
2 Yorum
Make sure you use the correct type brake fluid. A common issue especially with DOT5 is after bleeding the lever may not compress to activate the brakes. This is air in the fluid. DOT4 holds air as visible bubbles, while DOT5 holds air in microscopic bubbles. DOT4 holds water in suspension, while water in DOT5 will settle to the lowest part of the system usually in the calipers, which is why it is important to keep DOT5 systems bled. The cure for suspended air in DOT5 when renewing fluid is to squeeze the lever or pedal with the bleed valve closed, slipping your fingers off the lever releasing it rapidly with the master reservoir cap off. Notice if tiny bubbles come up into the reservoir. Also use a syringe with fluid attached to open bleed valve and force fresh fluid up into the system. With this technique you should be able to get some resistant pressure at the lever.