Eşyalarını Tamir Et Topluluk Mağaza

Honeytone N-10 Mini Amp Speaker Replacement

Yazan: Corey Brown
  • Yorumlar: 1
  • Favoriler: 1
  • Tamamlanma: 3

Zorluk

Orta

Adımlar

10

Gerekli Süre

20 dakika

Bölümler

1

İşaretler

1

Member-Contributed Guide

Üye Katkılı Kılavuz

Topluluğumuzun müthiş bir üyesi bu kılavuzu hazırladı. Bu kılavuz, iFixit personeli tarafından yönetilmiyor.

Giriş

Some soldering will be required in order to complete the speaker replacement.

  1. Flip your amp over to begin removing the plastic cover. Flip your amp over to begin removing the plastic cover.

    • Flip your amp over to begin removing the plastic cover.

    Düzenle

  2. Remove the battery cover and take the battery out. Unless you want a quick pick-me-up, in which case feel free to leave it in and get shocked.

    • Remove the battery cover and take the battery out.

    • Unless you want a quick pick-me-up, in which case feel free to leave it in and get shocked.

    Düzenle

  3. Unscrew the four corner screws using a phillips #0 screw driver to remove the back cover. While the screws are recessed deep into the cover and difficult to see, 2-4 turns will easily release them.

    • Unscrew the four corner screws using a phillips #0 screw driver to remove the back cover.

    • While the screws are recessed deep into the cover and difficult to see, 2-4 turns will easily release them.

    Düzenle

  4. Remove the back cover by carefully pushing the battery connector through the hole in the cover. Remove the back cover by carefully pushing the battery connector through the hole in the cover. Remove the back cover by carefully pushing the battery connector through the hole in the cover.

    • Remove the back cover by carefully pushing the battery connector through the hole in the cover.

    Düzenle

  6. With the phillips #0 screwdriver, unscrew the two white plastic clips that hold the speaker in place. With the phillips #0 screwdriver, unscrew the two white plastic clips that hold the speaker in place. With the phillips #0 screwdriver, unscrew the two white plastic clips that hold the speaker in place.

    • With the phillips #0 screwdriver, unscrew the two white plastic clips that hold the speaker in place.

    Düzenle

  7. Use flush wire cutters to remove black and red wires from the old speaker. Note: The black wire has already been removed in this example image.

    • Use flush wire cutters to remove black and red wires from the old speaker.

    • Note: The black wire has already been removed in this example image.

    Düzenle

  8. Connect the new speaker by soldering the black and red wires to the negative and positive connections respectively Connect the new speaker by soldering the black and red wires to the negative and positive connections respectively Connect the new speaker by soldering the black and red wires to the negative and positive connections respectively

    • Connect the new speaker by soldering the black and red wires to the negative and positive connections respectively

    Düzenle

  9. Connect the battery and turn the power on to test proper connection of the new speaker.

    • Connect the battery and turn the power on to test proper connection of the new speaker.

    • Some static is fine, this is the natural sound of the amp.

    • Careful not to touch any of the metal components inside while temporarily testing the connection.

    Düzenle

  10. Reverse steps 1-5 to complete repair.

    • Reverse steps 1-5 to complete repair.

    Düzenle

    • Connect the amp to your favorite instrument and test out the new sound!

    Düzenle
Bitiş Çizgisi

3 farklı kişi bu kılavuzu tamamladı.

Yazar

Corey Brown

Üyelik tarihi: 24-06-2016

7.484 İtibar

11 adet Kılavuz yazıldı

Rozetler: 33

+30 tane daha rozet

Bir Yorum

Cool. If mine doesn’t work, is it likely to be the speaker? Thanks.

hupaand - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 6

Son 30 gün: 26

Her zaman: 2,515