Eşyalarını Tamir Et Topluluk Mağaza

Hover-1 Horizon Left Balancing Sensor Replacement

Giriş

Is your hoverboard unbalanced or leaning to one side while riding? This is a guide to show you how to remove the left balance sensor tab on the Hover-1 Horizon, the most likely culprit to your problem. This guide requires a Phillips #2 and a Phillips #1 screwdriver.

Neye ihtiyacın var

  1. Hover-1 Horizon Left Balancing Sensor Replacement, Base Plate: adım 1, 2 resimden 1. Hover-1 Horizon Left Balancing Sensor Replacement, Base Plate: adım 1, 2 resimden 2.

    • Remove the six 12mm Phillips #2 screws holding the base plate.

    Düzenle

  2. Hover-1 Horizon Left Balancing Sensor Replacement: adım 2, 2 resimden 1. Hover-1 Horizon Left Balancing Sensor Replacement: adım 2, 2 resimden 2.

    • Remove the two 11mm Phillips #1 screws that hold the base plate to the body.

    Düzenle

  3. Hover-1 Horizon Left Balancing Sensor Replacement: adım 3, 3 resimden 1. Hover-1 Horizon Left Balancing Sensor Replacement: adım 3, 3 resimden 2. Hover-1 Horizon Left Balancing Sensor Replacement: adım 3, 3 resimden 3.

    • Remove the base plate by lifting it up.

    • The base plate is connected to the body with wires. The wires are long enough to set the base plate to the side.

    Düzenle

  4. Hover-1 Horizon Left Balancing Sensor Replacement, Left Gyroscope Sensor Board: adım 4, 3 resimden 1. Hover-1 Horizon Left Balancing Sensor Replacement, Left Gyroscope Sensor Board: adım 4, 3 resimden 2. Hover-1 Horizon Left Balancing Sensor Replacement, Left Gyroscope Sensor Board: adım 4, 3 resimden 3.

    • Remove the two connectors on either side of the board by lifting the tab and pulling out.

    • Remove the connector in the middle of the board by squeezing the tab and pulling up.

    Düzenle

  6. Hover-1 Horizon Left Balancing Sensor Replacement: adım 5, 2 resimden 1. Hover-1 Horizon Left Balancing Sensor Replacement: adım 5, 2 resimden 2.

    • Remove the four 11mm Phillips #1 screws that hold the cover on.

    Düzenle

  7. Hover-1 Horizon Left Balancing Sensor Replacement: adım 6, 3 resimden 1. Hover-1 Horizon Left Balancing Sensor Replacement: adım 6, 3 resimden 2. Hover-1 Horizon Left Balancing Sensor Replacement: adım 6, 3 resimden 3.

    • Remove the four 11mm Phillips #1 screws that attach the gyroscope board to the mount.

    • Lift the board to reveal the connections on the bottom.

    Düzenle

  8. Hover-1 Horizon Left Balancing Sensor Replacement: adım 7, 2 resimden 1. Hover-1 Horizon Left Balancing Sensor Replacement: adım 7, 2 resimden 2.

    • Remove the middle connector by squeezing the top of the tab and pulling up.

    Düzenle

  9. Hover-1 Horizon Left Balancing Sensor Replacement: adım 8, 3 resimden 1. Hover-1 Horizon Left Balancing Sensor Replacement: adım 8, 3 resimden 2. Hover-1 Horizon Left Balancing Sensor Replacement: adım 8, 3 resimden 3.

    • Remove the four 12mm Phillips #2 screws that hold the motherboard to the base.

    • Pull the motherboard away from the gyroscope by grabbing it with two hands and pulling it to the right .

    Düzenle

  10. Hover-1 Horizon Left Balancing Sensor Replacement: adım 9, 3 resimden 1. Hover-1 Horizon Left Balancing Sensor Replacement: adım 9, 3 resimden 2. Hover-1 Horizon Left Balancing Sensor Replacement: adım 9, 3 resimden 3.

    • Unclip the black connector by squeezing both sides and pulling them apart.

    Düzenle

  11. Hover-1 Horizon Left Balancing Sensor Replacement, Left Balancing Sensors: adım 10, 3 resimden 1. Hover-1 Horizon Left Balancing Sensor Replacement, Left Balancing Sensors: adım 10, 3 resimden 2. Hover-1 Horizon Left Balancing Sensor Replacement, Left Balancing Sensors: adım 10, 3 resimden 3.

    • Remove the three 10 mm Phillips #1 screws connecting the balance sensor to the hoverboard.

    • The balance sensor tabs are made of sensitive rubber. Screw them back on slowly, and do not over-tighten.

    Düzenle

  12. Hover-1 Horizon Left Balancing Sensor Replacement: adım 11, 2 resimden 1. Hover-1 Horizon Left Balancing Sensor Replacement: adım 11, 2 resimden 2.

    • Remove the sensor tab by carefully lifting it away from the hoverboard.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

4 tane daha katılımcı ile

Jesus

Üyelik tarihi: 10/08/18

85 İtibar

1 Kılavuz yazıldı

Rozetler: 2

Ekip

Cal Poly, Team S13-G6, White Fall 2018 Cal Poly, Team S13-G6, White Fall 2018 üyesi

CPSU-WHITE-F18S13G6

4 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 4

Son 30 gün: 9

Her zaman: 859