Eşyalarını Tamir Et Topluluk Mağaza

Hover-1 Nomad Outer Shell Replacement

Salt Önkoşul
Bu kılavuz yalnızca diğer kılavuzlar için bir ön koşul olarak kullanılmak üzere tasarlanmıştır. Tek başına eksiktir.

Giriş

Follow this guide to remove and replace the outer shell of your Hover-1 Nomad.

Neye ihtiyacın var

  1. Hover-1 Nomad Outer Shell Replacement, Outer Shell: adım 1, 3 resimden 1. Hover-1 Nomad Outer Shell Replacement, Outer Shell: adım 1, 3 resimden 2. Hover-1 Nomad Outer Shell Replacement, Outer Shell: adım 1, 3 resimden 3.

    • Break the two warranty stickers by poking a screwdriver through them or peeling them off.

    • Remove the following twenty screws by rotating the screwdriver counterclockwise:

    • Eight 16.2mm Phillips #2 screws

    • Eight 15mm Phillips #2 screws

    • Four 19.1mm Phillips #2 screws

    • The holes containing most of the screws are deep and narrow. A screwdriver with interchangable bits will not be able to reach them.

    • Do not over-tighten the screws during reassembly. Over-tightened screws can crack the plastic channels holding the shell to the frame of the hoverboard.

    Düzenle

  2. Hover-1 Nomad Outer Shell Replacement: adım 2, 3 resimden 1. Hover-1 Nomad Outer Shell Replacement: adım 2, 3 resimden 2. Hover-1 Nomad Outer Shell Replacement: adım 2, 3 resimden 3.

    • Use a nylon spudger to pry the metal handle away from the outer shell.

    • Rotate the metal handle toward the center of the hoverboard to unlock the plate from the retaining clips.

    • Lift the hoverboard off the metal handle.

    • Repeat for the handle on the other side of the hoverboard.

    Düzenle

  4. Hover-1 Nomad Outer Shell Replacement: adım 3, 1 resimden 1.

    • Lift the plastic cover on each side up and away from the device.

    • Multiple wires connect the circuit boards to the outer shell. Remove the shell gently to avoid damaging the wires or components.

    Düzenle

  5. Hover-1 Nomad Outer Shell Replacement: adım 4, 2 resimden 1. Hover-1 Nomad Outer Shell Replacement: adım 4, 2 resimden 2.

    • Disconnect the following wires by pinching the connector tabs and pulling the plugs out of the connectors:

    • Charging port wires

    • Speaker assembly wires

    • Power button wires

    • Headlight wires

    • Only the headlight wires need to be disconnected from the other circuit board.

    • Ensure the wires are connected to the correct ports on the circuit board during reassembly.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Bir başkası bu kılavuzu tamamladı.

Yazar

3 tane daha katılımcı ile

Samuel Frazee

Üyelik tarihi: 10/08/18

1.015 İtibar

7 adet Kılavuz yazıldı

Rozetler: 12

+9 tane daha rozet

Ekip

Cal Poly, Team S15-G1, White Fall 2018 Cal Poly, Team S15-G1, White Fall 2018 üyesi

CPSU-WHITE-F18S15G1

4 Üyeler

7 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 0

Her zaman: 54