Ana içeriğe geç

What you need

  1. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation), How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): adım 1, 2 resimden 1. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation), How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): adım 1, 2 resimden 2.
    • On the top of the printer, turn the injector counter-clockwise and pull the tab.

  2. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): adım 2, 3 resimden 1. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): adım 2, 3 resimden 2. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): adım 2, 3 resimden 3.
    • Insert your fingers in the center of the filament cartridge and slowly pull it away from the printer.

  3. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): adım 3, 1 resimden 1.
    • Place the cartridge face up and pry off the lid of the cartridge.

  4. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): adım 4, 2 resimden 1. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): adım 4, 2 resimden 2.
    • Gently flip the cartridge on its front and remove the two 2mm Hex screws using a Hex key.

  5. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): adım 5, 1 resimden 1.
    • Flip the cartridge face up and remove the gearbox and extractor tube.

  6. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): adım 6, 3 resimden 1. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): adım 6, 3 resimden 2. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): adım 6, 3 resimden 3.
    • Place your thumb on the front of the injector head and your middle finger on the needle.

    • Firmly pull the needle towards your thumb until the injector head cases cracks and pulls apart the case.

  7. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): adım 7, 2 resimden 1. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): adım 7, 2 resimden 2.
    • Heat the needle using a lighter, making sure that the flame does not touch the needle.

    • Using needle-nose pliers, pull the needle from the tube.

    • Do not touch the needle as it may still be hot.

  8. How to Remove a Filament Clog on a Cubify Cube 3D Printer (3rd Generation): adım 8, 1 resimden 1.
    • Insert a paper clip and turn until the clog is removed.

Sonuç

To reassemble your device, follow these instructions in reverse order.

Hector Vazquez

Üyelik tarihi: 23-10-2020

157 İtibar

1 Kılavuz yazıldı

0 Comments

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 2

Son 7 gün: 8

Son 30 gün: 30

Her zaman: 280