Ana içeriğe geç

Giriş

Is your front-turn signal light bulb in your 2011 Subaru Impreza Outback Sport going out? Use this guide to replace the dead bulb with a new one and have a working turn signal again.

  1. First, check to see if your front-turn signal is not working properly or not bright enough.
    • First, check to see if your front-turn signal is not working properly or not bright enough.

  2. Turn on your car and turn your wheels so that you have access to the headlights and front-turn signal. Make sure the car is in park and turned off before you begin making your repair.
    • Turn on your car and turn your wheels so that you have access to the headlights and front-turn signal.

    • Make sure the car is in park and turned off before you begin making your repair.

  3. Use a flathead screwdriver and your hand to loosen the panel. Pry the front bumper open away from the black panel.
    • Use a flathead screwdriver and your hand to loosen the panel.

    • Pry the front bumper open away from the black panel.

  4. Look inside of the bumper and up towards where the headlights and front-turn signal are. Locate the white bulb socket for the front-turn signal. Reach inside and grab the white bulb socket
    • Look inside of the bumper and up towards where the headlights and front-turn signal are.

    • Locate the white bulb socket for the front-turn signal.

    • Reach inside and grab the white bulb socket

    • Twist counter-clockwise to remove the bulb and socket from their position.

  5. You should see the bulb being removed from its front-turn signal location. You should see the bulb being removed from its front-turn signal location. You should see the bulb being removed from its front-turn signal location.
    • You should see the bulb being removed from its front-turn signal location.

  6. Pull the bulb socket and bulb out to an easy to handle area. Remove the nonfunctioning bulb from the bulb socket. Insert new bulb into the bulb socket and twist clockwise until it is tightly fastened.
    • Pull the bulb socket and bulb out to an easy to handle area.

    • Remove the nonfunctioning bulb from the bulb socket.

    • Insert new bulb into the bulb socket and twist clockwise until it is tightly fastened.

  7. Now your front-turn signal should be working properly.
    • Now your front-turn signal should be working properly.

Sonuç

To reassemble your device, follow these instructions in reverse order.

2 farklı kişi bu kılavuzu tamamladı.

Austin Roberts

Üyelik tarihi: 29-09-2015

155 İtibar

1 Kılavuz yazıldı

Takım

Cal Poly, Team 14-1, Green Fall 2015 Cal Poly, Team 14-1, Green Fall 2015 üyesi

CPSU-GREEN-F15S14G1

4 Üyeler

4 adet Kılavuz yazıldı

2 Yorum

I'm glad I looked here. I was ready to go in from above and move the battery so I could get at the bulb socket. This method was easier--and had the advantage of working, which I can't say was true of the approach I had in mind. The drive was wet and I didn't have my flashlight, so I did it all by feel., seated on an upended plastic bucket. Heavy rubber gloves might help. I almost scored the back of my hand, but managed to avoid that. Excellent advice.

vurbanowicz - Yanıt

My wheel well & bumper was a bit harder to remove (a few more plastic rivets holding it on) but I was able to get it open enough to reach up - easy enough to remove by feel. Thanks for the guide!

Steve Everett - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 8

Son 7 Gün: 37

Son 30 Gün: 207

Her zaman: 8,987