Ana içeriğe geç

Eşyalarını Tamir Et

Onarma Hakkı

Mağaza

  1. Use a Phillips #2 screwdriver to remove the two screws on the top of the device toward the back.
    • Use a Phillips #2 screwdriver to remove the two screws on the top of the device toward the back.

  2. Remove the plastic cover by lifting up the back and pulling it away from the faceplate.
    • Remove the plastic cover by lifting up the back and pulling it away from the faceplate.

  3. Find and unclip the three latches on the bottom of the device. Find and unclip the three latches on the bottom of the device.
    • Find and unclip the three latches on the bottom of the device.

  4. Pull the faceplate off.
    • Pull the faceplate off.

  5. Use a Phillips #2 screwdriver to unscrew the two screws at the base of the disc drive. (See image) Use a Phillips #2 screwdriver to unscrew the two screws at the base of the disc drive. (See image)
    • Use a Phillips #2 screwdriver to unscrew the two screws at the base of the disc drive. (See image)

  6. Use the screwdriver to remove two screws on either side of the silver security bar. Use the screwdriver to remove two screws on either side of the silver security bar.
    • Use the screwdriver to remove two screws on either side of the silver security bar.

  7. Pull out the silver security bar and set aside. Pull out the silver security bar and set aside.
    • Pull out the silver security bar and set aside.

  8. Take out the two screws on either side of the green circuit-board as seen in the photos.
    • Take out the two screws on either side of the green circuit-board as seen in the photos.

  9. Carefully lift the board just enough to remove the disc drive. Carefully lift the board just enough to remove the disc drive.
    • Carefully lift the board just enough to remove the disc drive.

  10. Unscrew the two screws at the back of the disc drive. Unscrew the two screws at the back of the disc drive. Unscrew the two screws at the back of the disc drive.
    • Unscrew the two screws at the back of the disc drive.

  11. Gently lift the disc drive out of the DVD player. The disc drive is still attached but you are now able to get to underneath it for cleaning and maintenance.
    • Gently lift the disc drive out of the DVD player.

    • The disc drive is still attached but you are now able to get to underneath it for cleaning and maintenance.

  12. Turn disc drive over so you can see the gears on the bottom. Turn disc drive over so you can see the gears on the bottom.
    • Turn disc drive over so you can see the gears on the bottom.

  13. Using a cotton swap or a cleansing cloth and alcohol, gently rub the gears ridding of any debris and dust. You can also use a compressed air can as well. Just point the nozzle at the gears and spray with the compressed air.
    • Using a cotton swap or a cleansing cloth and alcohol, gently rub the gears ridding of any debris and dust.

    • You can also use a compressed air can as well. Just point the nozzle at the gears and spray with the compressed air.

Sonuç

To reassemble your device, follow these instructions in reverse order.

2 farklı kişi bu kılavuzu tamamladı.

Taryn

Üyelik tarihi: 15-09-2011

103 İtibar

4 adet Kılavuz yazıldı

Takım

University of Maine, Team 1-2, Diaz Fall 2011 University of Maine, Team 1-2, Diaz Fall 2011 üyesi

UMAINE-DIAZ-F11S1G2

2 Üyeler

5 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 20

Her zaman: 705