Menü

Ayarlarınız

Tezgahım

Cihazlarınız için kılavuz, parça ve cevaplara hızlı erişim edinin
Sepetim

Sepetiniz boş görünüyor

Mağazamıza Göz Atın

India Mark III Chain Replacement

Yazan: Andrew Optimus Goldheart (ve 5 başka katılımcı)
  • Yorumlar: 0
  • Favoriler: 0

Zorluk

Orta

Adımlar

8

Gerekli Süre

Bir süre öner??

Bölümler

1

İşaretler

1

Prerequisite Only

Salt Önkoşul

Bu kılavuzun yalnızca diğer kılavuzlar için bir önkoşul kılavuzu olduğunu lütfen dikkate alın.

Giriş

Prereq only.

Aletler

Parçalar

Hiçbir parça belirtilmedi.

  1. Place the spacer collar around the pump rod below the raised chain, with the beveled side down, and the flat side facing up. Place the spacer collar around the pump rod below the raised chain, with the beveled side down, and the flat side facing up. Place the spacer collar around the pump rod below the raised chain, with the beveled side down, and the flat side facing up.

    • Place the spacer collar around the pump rod below the raised chain, with the beveled side down, and the flat side facing up.

    Düzenle

  2. The following procedure requires two people. If you attempt to do this alone, you risk injuring yourself and damaging the pump. Lift the pump handle until the base of the chain comes to rest on the spacer collar, and the chain is slack. Hold the handle in this position while the chain is being detached. Lift the pump handle until the base of the chain comes to rest on the spacer collar, and the chain is slack. Hold the handle in this position while the chain is being detached.

    • The following procedure requires two people. If you attempt to do this alone, you risk injuring yourself and damaging the pump.

    • Lift the pump handle until the base of the chain comes to rest on the spacer collar, and the chain is slack. Hold the handle in this position while the chain is being detached.

    Düzenle

  3. Using the two access holes, place an angled socket wrench on the bolt and nut attaching the chain to the pump handle. Using the two access holes, place an angled socket wrench on the bolt and nut attaching the chain to the pump handle. Using the two access holes, place an angled socket wrench on the bolt and nut attaching the chain to the pump handle.

    • Using the two access holes, place an angled socket wrench on the bolt and nut attaching the chain to the pump handle.

    Düzenle

  5. Hold the wrench on the bolt stationary. Loosen the nut. Loosen the nut.

    • Hold the wrench on the bolt stationary.

    • Loosen the nut.

    Düzenle

  6. Remove the nut from the chain bolt. Remove the nut from the chain bolt. Remove the nut from the chain bolt.

    • Remove the nut from the chain bolt.

    Düzenle

  7. Remove the washer from the chain bolt. Remove the washer from the chain bolt.

    • Remove the washer from the chain bolt.

    Düzenle

  8. Remove the chain bolt. Remove the chain bolt.

    • Remove the chain bolt.

    Düzenle

  9. Pull the top of the chain straight off of the pump handle. Pull the top of the chain straight off of the pump handle. Pull the top of the chain straight off of the pump handle.

    • Pull the top of the chain straight off of the pump handle.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

5 tane daha katılımcı ile

Andrew Optimus Goldheart

Üyelik tarihi: 17-10-2009

425.146 İtibar

411 adet Kılavuz yazıldı

Rozetler: 43

+40 tane daha rozet

Takım

iFixit iFixit üyesi

Community

104 Üyeler

9.208 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 0

Son 30 Gün: 0

Her zaman: 25