Eşyalarını Tamir Et Topluluk Mağaza

Installing Mercedes W166 RAV Tool Box

Neye ihtiyacın var

  1. Installing Mercedes W166 RAV Tool Box, RAV Tool Box: adım 1, 2 resimden 1. Installing Mercedes W166 RAV Tool Box, RAV Tool Box: adım 1, 2 resimden 2.

    • 1. Vehicle Preparation

    • Remove all loose items from the cargo area. Remove the cargo floor, spare wheel and tool tray.

    • Remove rear seats as in WIS instructions (Save seat mounting hardware)

    Düzenle

  2. Installing Mercedes W166 RAV Tool Box: adım 2, 3 resimden 1. Installing Mercedes W166 RAV Tool Box: adım 2, 3 resimden 2. Installing Mercedes W166 RAV Tool Box: adım 2, 3 resimden 3.

    • Remove bolt from rear deck sill plate

    • Unclip rear deck sill plate and remove.

    Düzenle

  3. Installing Mercedes W166 RAV Tool Box: adım 3, 1 resimden 1.

    • Remove plastic covers

    • Remove Felt liner

    Düzenle

  4. Installing Mercedes W166 RAV Tool Box: adım 4, 3 resimden 1. Installing Mercedes W166 RAV Tool Box: adım 4, 3 resimden 2. Installing Mercedes W166 RAV Tool Box: adım 4, 3 resimden 3.

    • Remove side consoles and center support (T30 10 Bolts)

    Düzenle

  5. Installing Mercedes W166 RAV Tool Box: adım 5, 3 resimden 1. Installing Mercedes W166 RAV Tool Box: adım 5, 3 resimden 2. Installing Mercedes W166 RAV Tool Box: adım 5, 3 resimden 3.

    • Install and bolt down center support bracket (2 Bolts M10 x 1.5 x35mm 6mm Allen cap, 10mm flat washers)

    • Pay attention to the pin to align properly

    • NOTE: To service TPMS control module remove drawers ad service through access door in bottom plate.

    Düzenle

  6. Installing Mercedes W166 RAV Tool Box: adım 6, 3 resimden 1. Installing Mercedes W166 RAV Tool Box: adım 6, 3 resimden 2. Installing Mercedes W166 RAV Tool Box: adım 6, 3 resimden 3.

    • 2. Installation of Front Box

    • Place box inside vehicle. It fits through the rear doors. This is a 2 person job.

    • Mount front legs on front consoles, tighten loosely (2 Bolts M10 x 1.5 x35mm 6mm Allen cap, 10mm flat washers). Pay attention not to break off the alignment pin, which will be inside the post after mounting.

    • DO NOT mount the box to the center bracket at this point

    Düzenle

  8. Installing Mercedes W166 RAV Tool Box: adım 7, 2 resimden 1. Installing Mercedes W166 RAV Tool Box: adım 7, 2 resimden 2.

    • 3. Installation of the rear plate

    • Install 6 rear support brackets and tighten finger tight

    Düzenle

  9. Installing Mercedes W166 RAV Tool Box: adım 8, 3 resimden 1. Installing Mercedes W166 RAV Tool Box: adım 8, 3 resimden 2. Installing Mercedes W166 RAV Tool Box: adım 8, 3 resimden 3.

    • Set plate on brackets and align, overlapping the base plate of the front box on the center support bracket.

    • Use punch tool to align holes and drop in 2 bolts M8 x 1.25 x 40mm in holes on each side and one bolt M8 x 1.25 x 30 in the center hole.

    Düzenle

  10. Installing Mercedes W166 RAV Tool Box: adım 9, 3 resimden 1. Installing Mercedes W166 RAV Tool Box: adım 9, 3 resimden 2. Installing Mercedes W166 RAV Tool Box: adım 9, 3 resimden 3.

    • Secure plate to center support bracket with 2 bolts on the outside and on in the middle, align and finger tighten

    Düzenle

  11. Installing Mercedes W166 RAV Tool Box: adım 10, 2 resimden 1. Installing Mercedes W166 RAV Tool Box: adım 10, 2 resimden 2.

    • Install 3 bolts securing base plate to vehicle frame

    • and 4th bolt securing the tool box rail to the base plate and vehicle frame.

    • Put bolt sizes in

    Düzenle

  12. Installing Mercedes W166 RAV Tool Box: adım 11, 2 resimden 1. Installing Mercedes W166 RAV Tool Box: adım 11, 2 resimden 2.

    • Install and loosely tighten 3 M8 black oxide bolts on each side until L bracket touches the underside of the base plate

    Düzenle

  13. Installing Mercedes W166 RAV Tool Box: adım 12, 2 resimden 1. Installing Mercedes W166 RAV Tool Box: adım 12, 2 resimden 2.

    • Fully tighten M8 (20 Nm)

    • Fully tighten M6 (8 Nm)

    Düzenle

  14. Installing Mercedes W166 RAV Tool Box: adım 13, 3 resimden 1. Installing Mercedes W166 RAV Tool Box: adım 13, 3 resimden 2. Installing Mercedes W166 RAV Tool Box: adım 13, 3 resimden 3.

    • Fully tighten M10 bolts (35 Nm)

    Düzenle

  15. Installing Mercedes W166 RAV Tool Box: adım 14, 3 resimden 1. Installing Mercedes W166 RAV Tool Box: adım 14, 3 resimden 2. Installing Mercedes W166 RAV Tool Box: adım 14, 3 resimden 3.

    • 4. Install box

    • Remove drawers and slide box on rail guides, align with bolt holes

    • Install 6 (M12) bolts and fully tighten to 66 Nm

    Düzenle

  16. Installing Mercedes W166 RAV Tool Box: adım 15, 3 resimden 1. Installing Mercedes W166 RAV Tool Box: adım 15, 3 resimden 2. Installing Mercedes W166 RAV Tool Box: adım 15, 3 resimden 3.

    • Install drawers.

    • After drawer is installed move rail clip to locked position

    Düzenle

  17. Installing Mercedes W166 RAV Tool Box: adım 16, 1 resimden 1.

    • Fasten seat belt with bolt to floor

    Düzenle
Bitiş Çizgisi

4 farklı kişi bu kılavuzu tamamladı.

Yazar

3 tane daha katılımcı ile

Stefan

Üyelik tarihi: 02/22/13

275 İtibar

1 Kılavuz yazıldı

Rozetler: 4

+1 tane daha rozet

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 11

Son 30 gün: 36

Her zaman: 3,882