Eşyalarını Tamir Et Topluluk Mağaza

Jumper Angelsounds JPD-100S Indicator Light Replacement

Giriş

Have a working knowledge of soldering before attempting to replace this part.

Neye ihtiyacın var

  1. Jumper Angelsounds JPD-100S Indicator Light Replacement, Motherboard: adım 1, 1 resimden 1.

    • Access the battery compartment

    • Remove the battery compartment lid and set it aside.

    • Disconnect the battery and set it aside.

    Düzenle

  2. Jumper Angelsounds JPD-100S Indicator Light Replacement: adım 2, 2 resimden 1. Jumper Angelsounds JPD-100S Indicator Light Replacement: adım 2, 2 resimden 2.

    • Puncture the sticker in the battery compartment with a spudger to access the screw beneath it.

    Düzenle

  3. Jumper Angelsounds JPD-100S Indicator Light Replacement: adım 3, 1 resimden 1.

    • Remove the 7mm Phillips #1 screw from the battery compartment.

    • Place the screw in a secure place.

    Düzenle

  5. Jumper Angelsounds JPD-100S Indicator Light Replacement: adım 4, 2 resimden 1. Jumper Angelsounds JPD-100S Indicator Light Replacement: adım 4, 2 resimden 2.

    • Begin prying open the device.

    • Insert a plastic opening tool into the side groove about 2cm from the pink plastic component and pry open one side of the device.

    • Once the side is separated, leave the opening tool inside to prevent the two sides from closing.

    Düzenle

  6. Jumper Angelsounds JPD-100S Indicator Light Replacement: adım 5, 2 resimden 1. Jumper Angelsounds JPD-100S Indicator Light Replacement: adım 5, 2 resimden 2.

    • Insert another plastic opening tool into the groove opposite to the side of the tool already inserted.

    • Create separation on that side until the white plastic component comes off entirely.

    • Place the white plastic component in a secure place.

    Düzenle

  7. Jumper Angelsounds JPD-100S Indicator Light Replacement: adım 6, 1 resimden 1.

    • With your hand, remove the pink component.

    Düzenle

  8. Jumper Angelsounds JPD-100S Indicator Light Replacement: adım 7, 1 resimden 1.

    • Remove the 7mm Phillips #1 screw in the middle of the motherboard.

    Düzenle

  9. Jumper Angelsounds JPD-100S Indicator Light Replacement, Indicator Light: adım 8, 1 resimden 1.

    • Place the motherboard in a position that allows access it's underside.

    • Pre-heat the soldering iron.

    Düzenle

  10. Jumper Angelsounds JPD-100S Indicator Light Replacement: adım 9, 3 resimden 1. Jumper Angelsounds JPD-100S Indicator Light Replacement: adım 9, 3 resimden 2. Jumper Angelsounds JPD-100S Indicator Light Replacement: adım 9, 3 resimden 3.

    • Desoldering

    • If steam is created when the soldering iron is touched to a wet sponge then the soldering iron is hot enough.

    • Use the soldering iron and soldering vacuum to unsolder the indicator light leads.

    • Plastic spacer holding indicator light may burn.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

3 tane daha katılımcı ile

Deron Rogers

Üyelik tarihi: 08/31/15

271 İtibar

2 adet Kılavuz yazıldı

Rozetler: 14

+11 tane daha rozet

Ekip

USF Tampa, Team 6-1, Remmell Fall 2015 USF Tampa, Team 6-1, Remmell Fall 2015 üyesi

USFT-REMMELL-F15S6G1

6 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 5

Son 30 gün: 7

Her zaman: 182