Eşyalarını Tamir Et Topluluk Mağaza

Jumper Angelsounds JPD-100S The Transducer Replacement

Giriş

Step by step, this guide will demonstrate how to change the transducer of the Angel Sound device

Neye ihtiyacın var

  1. Jumper Angelsounds JPD-100S The Transducer Replacement, Motherboard: adım 1, 1 resimden 1.

    • Access the battery compartment

    • Remove the battery compartment lid and set it aside.

    • Disconnect the battery and set it aside.

    Düzenle

  2. Jumper Angelsounds JPD-100S The Transducer Replacement: adım 2, 2 resimden 1. Jumper Angelsounds JPD-100S The Transducer Replacement: adım 2, 2 resimden 2.

    • Puncture the sticker in the battery compartment with a spudger to access the screw beneath it.

    Düzenle

  3. Jumper Angelsounds JPD-100S The Transducer Replacement: adım 3, 1 resimden 1.

    • Remove the 7mm Phillips #1 screw from the battery compartment.

    • Place the screw in a secure place.

    Düzenle

  5. Jumper Angelsounds JPD-100S The Transducer Replacement: adım 4, 2 resimden 1. Jumper Angelsounds JPD-100S The Transducer Replacement: adım 4, 2 resimden 2.

    • Begin prying open the device.

    • Insert a plastic opening tool into the side groove about 2cm from the pink plastic component and pry open one side of the device.

    • Once the side is separated, leave the opening tool inside to prevent the two sides from closing.

    Düzenle

  6. Jumper Angelsounds JPD-100S The Transducer Replacement: adım 5, 2 resimden 1. Jumper Angelsounds JPD-100S The Transducer Replacement: adım 5, 2 resimden 2.

    • Insert another plastic opening tool into the groove opposite to the side of the tool already inserted.

    • Create separation on that side until the white plastic component comes off entirely.

    • Place the white plastic component in a secure place.

    Düzenle

  7. Jumper Angelsounds JPD-100S The Transducer Replacement: adım 6, 1 resimden 1.

    • With your hand, remove the pink component.

    Düzenle

  8. Jumper Angelsounds JPD-100S The Transducer Replacement: adım 7, 1 resimden 1.

    • Remove the 7mm Phillips #1 screw in the middle of the motherboard.

    Düzenle

  9. Jumper Angelsounds JPD-100S The Transducer Replacement, The Transducer: adım 8, 1 resimden 1.

    • Unsolder the Black cable

    Düzenle

  10. Jumper Angelsounds JPD-100S The Transducer Replacement: adım 9, 2 resimden 1. Jumper Angelsounds JPD-100S The Transducer Replacement: adım 9, 2 resimden 2.

    • Unsolder the red cables from the metal plates.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

1 tane daha katılımcı ile

Muosa Almubarak

Üyelik tarihi: 09/29/15

101 İtibar

1 Kılavuz yazıldı

Rozetler: 2

Ekip

USF Tampa, Team 6-1, Remmell Fall 2015 USF Tampa, Team 6-1, Remmell Fall 2015 üyesi

USFT-REMMELL-F15S6G1

6 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 1

Son 30 gün: 3

Her zaman: 287