Menü

Ayarlarınız

Kenwood DNX571HD CD/DVD Drive Replacement

Yazan: Wendy Zaballos (ve 4 başka katılımcı)
  • Yorumlar: 0
  • Favoriler: 0
  • Tamamlanma: 1

Zorluk

Kolay

Adımlar

6

Gerekli Süre

5 - 10 dakika

Bölümler

1

İşaretler

0

Giriş

If the CD/DVD drive in your Kenwood DNX571HD car stereo has stopped working, or has physically broken, follow this guide to remove the module and replace it with a new one.

Aletler

Bu aletleri satın al

Parçalar

Hiçbir parça belirtilmedi.

  1. Unscrew the four 3.5mm side screws with a Phillips #1 screwdriver. There are two screws per side.

    • Unscrew the four 3.5mm side screws with a Phillips #1 screwdriver.

    • There are two screws per side.

    Düzenle

  2. Use a spudger to unhook the plastic clips on the sides and top of the front panel. There are two clips on each side and one clip on the top. Place the spudger between the plastic tab and the metal case and gently lift the spudger away from the case. Place the spudger between the plastic tab and the metal case and gently lift the spudger away from the case.

    • Use a spudger to unhook the plastic clips on the sides and top of the front panel. There are two clips on each side and one clip on the top.

    • Place the spudger between the plastic tab and the metal case and gently lift the spudger away from the case.

    Düzenle

  4. Pull the top of the front panel out and down to remove front panel.

    • Pull the top of the front panel out and down to remove front panel.

    • Remove the front panel gently so as not to damage the ribbon cables behind it.

    Düzenle

  5. Unscrew the three 5mm screws from the top of the device using a Phillips #1 screwdriver. Lift up to remove the top casing. Lift up to remove the top casing.

    • Unscrew the three 5mm screws from the top of the device using a Phillips #1 screwdriver.

    • Lift up to remove the top casing.

    Düzenle

  6. Lift the CD drive carefully to expose the attached cable underneath.

    • Lift the CD drive carefully to expose the attached cable underneath.

    Düzenle

  7. Flip up the black clasp with a spudger to disconnect the large white ribbon cable connecting the CD drive to the board underneath. Flip up the black clasp with a spudger to disconnect the large white ribbon cable connecting the CD drive to the board underneath.

    • Flip up the black clasp with a spudger to disconnect the large white ribbon cable connecting the CD drive to the board underneath.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Bir başkası bu kılavuzu tamamladı.

Yazar

4 tane daha katılımcı ile

Wendy Zaballos

Üyelik tarihi: 17-09-2018

838 İtibar

6 adet Kılavuz yazıldı

Rozetler: 4

+1 tane daha rozet

Takım

Washington State, Team S1-G1, Hope Fall 2018 Washington State, Team S1-G1, Hope Fall 2018 üyesi

WSU-HOPE-F18S1G1

4 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 2

Son 30 gün: 12

Her zaman: 165