Eşyalarını Tamir Et

Onarma Hakkı

Mağaza

Kenwood DNX571HD GPS Antenna Connection Replacement

Yazan: Wendy Zaballos (ve 3 başka katılımcı)
  • Yorumlar: 0
  • Favoriler: 0

Zorluk

Zor

Adımlar

20

Gerekli Süre

30 dakika - 2 saat

Bölümler

3

İşaretler

0

Giriş

If you are having difficulties with the Kenwood DNX571HD GPS functions, the antenna may be faulty. Follow this guide to replace it.

  1. Unscrew the four 3.5mm side screws with a Phillips #1 screwdriver. There are two screws per side.

    • Unscrew the four 3.5mm side screws with a Phillips #1 screwdriver.

    • There are two screws per side.

    Düzenle

  2. Use a spudger to unhook the plastic clips on the sides and top of the front panel. There are two clips on each side and one clip on the top. Place the spudger between the plastic tab and the metal case and gently lift the spudger away from the case. Place the spudger between the plastic tab and the metal case and gently lift the spudger away from the case.

    • Use a spudger to unhook the plastic clips on the sides and top of the front panel. There are two clips on each side and one clip on the top.

    • Place the spudger between the plastic tab and the metal case and gently lift the spudger away from the case.

    Düzenle

  3. Pull the top of the front panel out and down to remove front panel.

    • Pull the top of the front panel out and down to remove front panel.

    • Remove the front panel gently so as not to damage the ribbon cables behind it.

    Düzenle

  4. Unscrew the three 5mm screws from the top of the device using a Phillips #1 screwdriver. Lift up to remove the top casing. Lift up to remove the top casing.

    • Unscrew the three 5mm screws from the top of the device using a Phillips #1 screwdriver.

    • Lift up to remove the top casing.

    Düzenle

  5. Lift the CD drive carefully to expose the attached cable underneath.

    • Lift the CD drive carefully to expose the attached cable underneath.

    Düzenle

  6. Flip up the black clasp with a spudger to disconnect the large white ribbon cable connecting the CD drive to the board underneath. Flip up the black clasp with a spudger to disconnect the large white ribbon cable connecting the CD drive to the board underneath.

    • Flip up the black clasp with a spudger to disconnect the large white ribbon cable connecting the CD drive to the board underneath.

    Düzenle

  7. Carefully unplug the fan power cord with the tweezers.

    • Carefully unplug the fan power cord with the tweezers.

    Düzenle

  9. Unscrew the three 5mm length screws with the Phillips #1 screwdriver. Remove the metal plate

    • Unscrew the three 5mm length screws with the Phillips #1 screwdriver.

    • Remove the metal plate

    • Removing the plate will damage the heat sink compound. This will need to be replaced during reassembly.

    Düzenle

  10. Unscrew the three 5.5mm long screws with a Phillips #1 screwdriver. Unscrew the three 5.5mm long screws with a Phillips #1 screwdriver.

    • Unscrew the three 5.5mm long screws with a Phillips #1 screwdriver.

    Düzenle

  11. Remove the four 5.5mm screws with the Phillips #1 screwdriver. Remove the four 5.5mm screws with the Phillips #1 screwdriver. Remove the four 5.5mm screws with the Phillips #1 screwdriver.

    • Remove the four 5.5mm screws with the Phillips #1 screwdriver.

    Düzenle

  12. Lift the top part of the unit up from the lower chassis.

    • Lift the top part of the unit up from the lower chassis.

    Düzenle

  13. Remove the two 13mm long screws with a Phillips #1 screwdriver. Gently thread the power cable through the circuit boards to separate the fan from the body of the stereo.

    • Remove the two 13mm long screws with a Phillips #1 screwdriver.

    • Gently thread the power cable through the circuit boards to separate the fan from the body of the stereo.

    Düzenle

  14. Using a spudger, undo the clasp to disconnect the large white ribbon cable. Using a spudger, undo the clasp to disconnect the large white ribbon cable.

    • Using a spudger, undo the clasp to disconnect the large white ribbon cable.

    Düzenle

  15. Remove the 5mm screw with teeth from the casing with a Phillips #1 screwdriver.

    • Remove the 5mm screw with teeth from the casing with a Phillips #1 screwdriver.

    Düzenle

  16. Remove the four 5mm screws with a Phillips #1 screwdriver.

    • Remove the four 5mm screws with a Phillips #1 screwdriver.

    Düzenle

  17. Remove the 5.5mm screw from the HDMI cable cover using a Phillips #2 screwdriver. Remove the 5.5mm screw from the HDMI cable cover using a Phillips #2 screwdriver.

    • Remove the 5.5mm screw from the HDMI cable cover using a Phillips #2 screwdriver.

    Düzenle

  18. Remove the 5mm screw with a Phillips #1 screwdriver.

    • Remove the 5mm screw with a Phillips #1 screwdriver.

    Düzenle

  19. Remove the two 5.5mm screws from the back. Lift the upper portion of the stereo free from the chassis.

    • Remove the two 5.5mm screws from the back.

    • Lift the upper portion of the stereo free from the chassis.

    Düzenle

  20. Remove the two screws underneath the GPS connector. Desolder the GPS connector.

    • Remove the two screws underneath the GPS connector.

    • Desolder the GPS connector.

    • The GPS antenna is a thru-hole-mounted device. You must apply heat to each soldered pin individually and pull them out of the holes while the solder is molten.

    • The solder material, pins, and any surrounding material will get VERY hot while melting the connections. Do not touch any metal parts during the desoldering process and give the device time to cool off once you’re finished. It may also be good to take breaks so that the electronics aren’t kept hot for extended periods of time.

    Düzenle

  21. To remove and reinsert the connector, on the top side of the board, use your finger to gently lift the metal plate to get enough clearance.

    • To remove and reinsert the connector, on the top side of the board, use your finger to gently lift the metal plate to get enough clearance.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

3 tane daha katılımcı ile

Wendy Zaballos

Üyelik tarihi: 17-09-2018

886 İtibar

6 adet Kılavuz yazıldı

Rozetler: 7

+4 tane daha rozet

Takım

Washington State, Team S1-G1, Hope Fall 2018 Washington State, Team S1-G1, Hope Fall 2018 üyesi

WSU-HOPE-F18S1G1

4 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 3

Son 30 gün: 16

Her zaman: 334