Menü

Ayarlarınız

Tezgahım

Cihazlarınız için kılavuz, parça ve cevaplara hızlı erişim edinin
Sepetim

Sepetiniz boş görünüyor

Mağazamıza Göz Atın

Kindle 1st Generation ON/OFF Power and Wifi Switches Replacement

Yazan: Samantha Manning (ve 4 başka katılımcı)
  • Yorumlar: 1
  • Favoriler: 0
  • Tamamlanma: 1

Zorluk

Orta

Adımlar

7

Gerekli Süre

5 - 10 dakika

Bölümler

2

İşaretler

0

Giriş

This guide goes through the process to replace the ON/OFF Power and Wifi Switches on the First Generation Amazon Kindle.

Aletler

Bu aletleri satın al

Parçalar

Hiçbir parçaya gerek yok.

  1. Slide the grey plastic cover laterally off the back of the device.

    • Slide the grey plastic cover laterally off the back of the device.

    Düzenle

  2. Use a plastic opening tool to lift the battery on the side closest to the edge of the device. Unplug the battery from the device by pinching the white connector and pulling.

    • Use a plastic opening tool to lift the battery on the side closest to the edge of the device.

    • Unplug the battery from the device by pinching the white connector and pulling.

    • Do not yank the battery or try to disconnect the battery by pulling the wires.

    Düzenle

  3. Unscrew eight (8) Phillips #00 screws (3 mm).

    • Unscrew eight (8) Phillips #00 screws (3 mm).

    Düzenle

  4. Pro Tech Toolkit içeren veya $100,00tüm siparişlerde ücretsiz kargo!

    Mağazamıza Göz Atın

  5. Start at one side of the device. Use a soft plastic prying tool to separate the casing of the device. Slowly work your way around the entire device. Avoid prying between the buttons and the device. This could cause damage to the buttons.

    • Start at one side of the device. Use a soft plastic prying tool to separate the casing of the device. Slowly work your way around the entire device.

    • Avoid prying between the buttons and the device. This could cause damage to the buttons.

    Düzenle

  6. Unscrew the two (2) Phillips #00 screws (3 mm) which fasten the metal casing shield. Slowly remove the metal casing shield by lifting it and carefully peeling up the tape.

    • Unscrew the two (2) Phillips #00 screws (3 mm) which fasten the metal casing shield.

    • Slowly remove the metal casing shield by lifting it and carefully peeling up the tape.

    Düzenle

  7. Remove the two (2) Phillips #00 screws (3 mm) which fasten the ON/OFF Power and Wifi Switches to the device.

    • Remove the two (2) Phillips #00 screws (3 mm) which fasten the ON/OFF Power and Wifi Switches to the device.

    Düzenle

  8. Lift the flap attaching the blue and white ribbon cable to the motherboard by lifting it vertically with the pointed-end of the spudger. The flap is connected via a hinge. Once you lift the flap, it will stay up and the cable will be lose. Remember to snap it back down during reassembly.

    • Lift the flap attaching the blue and white ribbon cable to the motherboard by lifting it vertically with the pointed-end of the spudger.

    • The flap is connected via a hinge. Once you lift the flap, it will stay up and the cable will be lose. Remember to snap it back down during reassembly.

    • Carefully lift the ON/OFF Power and Wifi Switch vertically from the device motherboard.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Bir başkası bu kılavuzu tamamladı.

0 Yorum

Yorum Ekle
İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 Gün: 2

Son 30 Gün: 8

Her zaman: 1,348