Turn off the cell phone and place face down on a flat surface.
  • Turn off the cell phone and place face down on a flat surface.

Yorum Ekle

While sliding the gray tab up, lift battery up and away from the cell phone. While sliding the gray tab up, lift battery up and away from the cell phone.
  • While sliding the gray tab up, lift battery up and away from the cell phone.

Yorum Ekle

Remove battery and set aside. Remove battery and set aside. Remove battery and set aside.
  • Remove battery and set aside.

Yorum Ekle

Use a Spudger to remove the two front plastic covers to reveal screws. Use a Spudger to remove the two front plastic covers to reveal screws.
  • Use a Spudger to remove the two front plastic covers to reveal screws.

Yorum Ekle

Remove two screws using a Torx T6 screwdriver.
  • Remove two screws using a Torx T6 screwdriver.

Yorum Ekle

Pry off the screen front cover with a small flathead screwdriver. Pry off the screen front cover with a small flathead screwdriver.
  • Pry off the screen front cover with a small flathead screwdriver.

Yorum Ekle

Mac RAM Kitleri
Mac'inizi hızlandırın. Hafızasını en yükseğe çıkar.
Mac RAM Kitleri
Mac'inize daha fazla bellek alın.
Insert a small flathead screwdriver into the hinge and separate hinge connection.
  • Insert a small flathead screwdriver into the hinge and separate hinge connection.

Yorum Ekle

Pry off the speaker which is glued on to the front cover using a small flathead screwdriver.
  • Pry off the speaker which is glued on to the front cover using a small flathead screwdriver.

Yorum Ekle

Remove remaining portion of the front case from the flexible circuit board.
  • Remove remaining portion of the front case from the flexible circuit board.

  • Do not attempt to remove the LCD board at this time, as it is attached to the rear panel assembly.

Yorum Ekle

Unscrew the four screws on the back case using a T6 Torx Screwdriver. Unscrew the four screws on the back case using a T6 Torx Screwdriver.
  • Unscrew the four screws on the back case using a T6 Torx Screwdriver.

Yorum Ekle

Pull the back cover straight off the phone using your thumb and forefinger. Pull the back cover straight off the phone using your thumb and forefinger.
  • Pull the back cover straight off the phone using your thumb and forefinger.

Yorum Ekle

Pry off circuit board with a flathead screwdriver.
  • Pry off circuit board with a flathead screwdriver.

Yorum Ekle

Pull out flexible keypad.
  • Pull out flexible keypad.

Yorum Ekle

The phone should now look like the picture to the left.
  • The phone should now look like the picture to the left.

Yorum Ekle

Locate and detach the ribbon cable from circuit board. Locate and detach the ribbon cable from circuit board.
  • Locate and detach the ribbon cable from circuit board.

Yorum Ekle

Remove the LCD Screen from the phone case and replace with a new LCD screen. Remove the LCD Screen from the phone case and replace with a new LCD screen.
  • Remove the LCD Screen from the phone case and replace with a new LCD screen.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

2 başka kişi bu kılavuzu tamamladı.

Nicholas Schmidt

Üyelik tarihi: 09-10-2010

97 İtibar

14 adet Kılavuz yazıldı

Takım

Cal Poly, Team 3-25, Regan Fall 2010 Cal Poly, Team 3-25, Regan Fall 2010 üyesi

CPSU-REGAN-F10S3G25

4 Üyeler

14 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 1

Son 30 Gün: 1

Her zaman: 796