Giriş

The following guide will show the complete tear down of the phone in order to replace the internal phone casing.

Remove the battery cover by placing your thumb on the small ridge near the top of the phone back and push downward, exposing the battery.
  • Remove the battery cover by placing your thumb on the small ridge near the top of the phone back and push downward, exposing the battery.

  • Our device did not come with a battery cover so it is not shown here.

  • Remove the battery using your finger to pry it out of the battery housing.

Yorum Ekle

Remove the (2) rubber screw covers located near the hinge of the phone using tweezers or a thumb tack.
  • Remove the (2) rubber screw covers located near the hinge of the phone using tweezers or a thumb tack.

  • Unscrew the (4) 3.6mm screws using a #00 Phillip's head screw driver.

Yorum Ekle

  • Carefully pry off the phone's backing using a plastic opening tool.

  • Slip the tool into the crack between the keypad (front panel) and the back panel.

  • Slide the tool along the sides of the phone to detach the tabs holding the backing on.

Yorum Ekle

  • Peel back the sticker with tweezers and hold it back with your finger.

  • Use the tweezers to lift the display adapter off the logic board.

Yorum Ekle

  • Lift the mother board out of the phone casing.

  • The keyboard can be easily removed once the mother board is out of the phone.

Yorum Ekle

  • Carefully pry off the black plastic screen cover using the iSesamo tool or another thin, flat tool.

  • The screen cover is adhered to the phone and may take some effort to pry off. If it is too difficult to remove, heat the screen with a hair dryer on low for 30 seconds to soften the adhesive.

Yorum Ekle

  • Unscrew the (4) 3.6mm screws near each corner of the phone's display panel by using a #00 Phillips head screwdriver.

  • The bottom two screws may have small rubber covers that you can remove using tweezers.

Yorum Ekle

  • Pry off the front panel of the phone using a Plastic Opening Tool.

    • Push the tool into the crack along the side of the phone.

    • Slide the tool along the crack to detach the tabs holding the backing on the phone.

Yorum Ekle

  • Use the tweezers to lift the display adapter off the screen component.

Yorum Ekle

  • Using tweezers remove the speaker from its casing.

  • The speaker is adhered to the phone casing so it will take a small amount of force to remove it.

Yorum Ekle

  • Remove the earpiece and gyroscope by lifting them out of the phone casing using tweezers.

  • The earpiece and gyroscope are adhered to the phone casing so it will take a small amount of force to remove them.

  • Be careful when removing these components as the connecting wires are easily broken/disconnected.

Yorum Ekle

  • Lift the screen components out of the phone.

Yorum Ekle

  • The phone is now fully disassembled.

  • Replace the parts indicated with your new phone casing.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

2 başka kişi bu kılavuzu tamamladı.

Henry

Üyelik tarihi: 12-04-2012

181 İtibar

3 adet Kılavuz yazıldı

Takım

Cal Poly, Team 7-33, Maness Spring 2012 Cal Poly, Team 7-33, Maness Spring 2012 üyesi

CPSU-MANESS-S12S7G33

4 Üyeler

10 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 0

Son 30 Gün: 1

Her zaman: 446