İptal Et

LG VX6000 Screen Replacement

Yazan: Adam Altman (ve 17 başka katılımcı)

Yorumlar: 1
Favoriler: 0

LG VX6000 Screen Replacement

Zorluk

Orta

Adımlar

15

Gerekli Süre

30 dakika

Giriş

The following guide is to remove or replace the screen of the LG VX6000 cellphone.

Aletler

Bu aletleri satın al

Parçalar

Hiçbir parçaya gerek yok.

Adım 1 Battery

Locate the dark gray tab on the back of the phone towards the top. Push the tab towards the top of the phone to release the battery.

Locate the dark gray tab on the back of the phone towards the top. Push the tab towards the top of the phone to release the battery.

Adım 2

Remove the battery by lifting up and rotating the battery away from the bottom edge.

Remove the battery by lifting up and rotating the battery away from the bottom edge.

Adım 3 Body

Pull out the two rubber cushions located on the top of the phone using tweezers.

Pull out the two rubber cushions located on the top of the phone using tweezers.
Only remove the two cushions that are circled!

Adım 4

Unscrew the six screws seen on the back using a Phillips 00 Screwdriver.

Unscrew the six screws seen on the back using a Phillips 00 Screwdriver.
Remove screws and carefully place on an uncluttered surface or in a small container.

Adım 5

Carefully remove the back of the phone gently using your fingernails or tweezers.

Carefully remove the back of the phone gently using your fingernails or tweezers.
There are a pair of red and blue wires that plugs into the motherboard. These wires will snap if you force the pieces apart.
To reattach the back, you must plug these wires back in.

Adım 6 Logic Board

Carefully peel off the adhesive tab as shown in the photo

Carefully peel off the adhesive tab as shown in the photo
The tab should not fully separate from the phone.

Adım 7

Locate the yellow connection towards the top of the phone. This is directly connected to the screen.

Remove the connector by carefully prying it away from the motherboard and lifting it away from the phone

Locate the yellow connection towards the top of the phone. This is directly connected to the screen.
Remove the connector by carefully prying it away from the motherboard and lifting it away from the phone
Do not pull too hard on the connector.

Adım 8

Gently lift a corner of the motherboard away from the casing to remove.

Gently lift a corner of the motherboard away from the casing to remove.

Adım 9 Screen

Using a paper clip or tweezers, pop out the screen by pressing the plastic tab in the top-left corner of the phone's bottom casing as indicated in the photo.

Be careful not to lose the tab that pops out. It is a small and clear piece of plastic.

The tab is fragile, handle with care.

Using a paper clip or tweezers, pop out the screen by pressing the plastic tab in the top-left corner of the phone's bottom casing as indicated in the photo.
Be careful not to lose the tab that pops out. It is a small and clear piece of plastic.
The tab is fragile, handle with care.

Adım 10

As shown in the photos, pull the orange strip through a thin opening at the top of the phone. Once this is done, the top and bottom halves can be separated.

As shown in the photos, pull the orange strip through a thin opening at the top of the phone. Once this is done, the top and bottom halves can be separated.

As shown in the photos, pull the orange strip through a thin opening at the top of the phone. Once this is done, the top and bottom halves can be separated.

As shown in the photos, pull the orange strip through a thin opening at the top of the phone. Once this is done, the top and bottom halves can be separated.

Adım 11

Set the bottom half of the phone aside.

Set the bottom half of the phone aside.
Using tweezers, pull off the small rubber cushions located towards the four corners of the screen.

Adım 12

With a Phillips tip screwdriver, unscrew the four newly exposed screws.

With a Phillips tip screwdriver, unscrew the four newly exposed screws.
Keep screws from the different steps in different locations so as to not mix them up.

Adım 13

Carefully open the casing using the iFixit plastic tool by prying each side a little bit at a time. Rotate and open until all the inside clips pop open and the casing opens up.

Carefully open the casing using the iFixit plastic tool by prying each side a little bit at a time. Rotate and open until all the inside clips pop open and the casing opens up.

Carefully open the casing using the iFixit plastic tool by prying each side a little bit at a time. Rotate and open until all the inside clips pop open and the casing opens up.

Carefully open the casing using the iFixit plastic tool by prying each side a little bit at a time. Rotate and open until all the inside clips pop open and the casing opens up.

Adım 14

After you pry open the casing, you will be left with the screen and circuit board in the top face plate.

Gently pull the corner of screen and circuit board up and out of casing to remove screen from the top face plate.

After you pry open the casing, you will be left with the screen and circuit board in the top face plate.
Gently pull the corner of screen and circuit board up and out of casing to remove screen from the top face plate.
Do not try to completely separate the circuit board from the casing. There are still wires connecting the two.

Adım 15

Rotate the screen and the connected white frame away from the logic board.

Rotate the screen and the connected white frame away from the logic board.
Carefully peel the adhesive tape that connects the screen and logic board off. The screen can now be removed and replaced with a new screen unit.

Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

17 tane daha katılımcı ile

Adam Altman

Üyelik tarihi: 14-01-2010

1 İtibar

3 adet Kılavuz yazıldı

+2 tane daha rozet

Takım

Cal Poly, Team 4-11, Forte Winter 2010 Cal Poly, Team 4-11, Forte Winter 2010 üyesi

CPSU-FORTE-W10S4G11

5 Üyeler

10 adet Kılavuz yazıldı

0 Yorum

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 0

Son 30 Gün: 2

Her zaman: 2,554