Eşyalarını Tamir Et

Onarma Hakkı

Mağaza

Lenovo IdeaCentre AIO 510S-23ISU Hard Drive Replacement

Yazan: Jackson Blake (ve 3 başka katılımcı)
  • Yorumlar: 2
  • Favoriler: 0
  • Tamamlanma: 11

Zorluk

Orta

Adımlar

9

Gerekli Süre

5 - 10 dakika

Bölümler

3

İşaretler

1

Featured Student Guide

Öne Çıkan Öğrenci Kılavuzu

Bu kılavuz, çalışkan öğrencilerimizin alın teriyle üretildi ve iFixit kadrosu tarafından epey havalı bulunuyor.

Giriş

This requires only a Phillips head screwdriver. Be aware that only 2.5" hard drives fit in this computer.

  1. Turn off the computer, unplug all cables, and let it cool down. Lay the computer flat on its screen.

    • Turn off the computer, unplug all cables, and let it cool down. Lay the computer flat on its screen.

    • Make sure that the work surface is flat and has nothing sharp on it.

    Düzenle

  2. Remove the monitor stand screw in the bottom of the stand, and remove the stand completely. Remove the monitor stand screw in the bottom of the stand, and remove the stand completely.

    • Remove the monitor stand screw in the bottom of the stand, and remove the stand completely.

    Düzenle

  3. Remove the two screws on the bottom of the computer, one on each side.

    • Remove the two screws on the bottom of the computer, one on each side.

    Düzenle

  4. The Essential Toolkit

    The most helpful tools in our most compact kit.

    Hemen Alışveriş Yapın

    The Essential Toolkit

    The most helpful tools in our most compact kit.

    Hemen Alışveriş Yapın

  5. Locate the slot on the right side of the computer next to the screw hole. Use a plastic opening tool or spudger to pry off the rear cover. (Don’t be afraid to use a little force.) Locate the slot on the right side of the computer next to the screw hole. Use a plastic opening tool or spudger to pry off the rear cover. (Don’t be afraid to use a little force.) Locate the slot on the right side of the computer next to the screw hole. Use a plastic opening tool or spudger to pry off the rear cover. (Don’t be afraid to use a little force.)

    • Locate the slot on the right side of the computer next to the screw hole. Use a plastic opening tool or spudger to pry off the rear cover. (Don’t be afraid to use a little force.)

    Düzenle

  6. Once it has been separated, lift to remove. Once it has been separated, lift to remove.

    • Once it has been separated, lift to remove.

    Düzenle

  7. Unscrew the four screws that secure the hard drive enclosure. Unscrew the four screws that secure the hard drive enclosure.

    • Unscrew the four screws that secure the hard drive enclosure.

    Düzenle

  8. Unplug the SATA cable. Lift to remove the hard drive enclosure.

    • Unplug the SATA cable. Lift to remove the hard drive enclosure.

    Düzenle

  9. Unscrew the four screws that hold hard drive enclosure to the hard drive, located on the side of the enclosure. Unscrew the four screws that hold hard drive enclosure to the hard drive, located on the side of the enclosure.

    • Unscrew the four screws that hold hard drive enclosure to the hard drive, located on the side of the enclosure.

    Düzenle

  10. Lift the hard drive up to remove it from the enclosure.

    • Lift the hard drive up to remove it from the enclosure.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

11 farklı kişi bu kılavuzu tamamladı.

Yazar

3 tane daha katılımcı ile

Jackson Blake

Üyelik tarihi: 22-01-2018

1.062 İtibar

9 adet Kılavuz yazıldı

Rozetler: 10

+7 tane daha rozet

Takım

Cal Poly, Team S16-G3, Banghart Winter 2018 Cal Poly, Team S16-G3, Banghart Winter 2018 üyesi

CPSU-BANGHART-W18S16G3

4 Üyeler

9 adet Kılavuz yazıldı

2 Yorum

Yorum Ekle

you have been busy!!!!! Noticed the solutions , etc. below and that is impressive. chaosone7 @gmail.com

Bobby Kincannon - Yanıt

It’s nice and easy to get there, unfortunately the board was fried lol.

Charles Allen - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 5

Son 7 gün: 76

Son 30 gün: 302

Her zaman: 8,401