Eşyalarını Tamir Et Topluluk Mağaza

Lenovo Yoga Tab 3 10 Motherboard Replacement

Neye ihtiyacın var

  1. Lenovo Yoga Tab 3 10 Motherboard Replacement, Back Cover: adım 1, 1 resimden 1.

    • Open the built-in kickstand.

    Düzenle

  2. Lenovo Yoga Tab 3 10 Motherboard Replacement: adım 2, 3 resimden 1. Lenovo Yoga Tab 3 10 Motherboard Replacement: adım 2, 3 resimden 2. Lenovo Yoga Tab 3 10 Motherboard Replacement: adım 2, 3 resimden 3.

    • Remove the sticker located directly under the the built-in kickstand to reveal two 0.75 mm screws.

    • Remove the microSD card slot cover. Remove any microSD card (if inserted).

    • Using a Phillips head screwdriver, remove the three 0.75 mm screws.

    Düzenle

  4. Lenovo Yoga Tab 3 10 Motherboard Replacement: adım 3, 3 resimden 1. Lenovo Yoga Tab 3 10 Motherboard Replacement: adım 3, 3 resimden 2. Lenovo Yoga Tab 3 10 Motherboard Replacement: adım 3, 3 resimden 3.

    • Orient the device so the screen is facing you.

    • Carefully insert the spudger along the seam between the screen and back cover and gently separate the back cover from the device frame.

    • Continue to detach the backplate from the frame by moving the spudger around the perimeter.

    • Some force will be required to detach the small plastic braces securing the backplate to the device.

    Düzenle

  5. Lenovo Yoga Tab 3 10 Motherboard Replacement, Motherboard: adım 4, 3 resimden 1. Lenovo Yoga Tab 3 10 Motherboard Replacement, Motherboard: adım 4, 3 resimden 2. Lenovo Yoga Tab 3 10 Motherboard Replacement, Motherboard: adım 4, 3 resimden 3.

    • Locate the screws in the motherboard the wire cover assembly and the speakers.

    • Use the J000 screwdriver to remove the screws on the motherboard, the wire cover, and the two speakers.

    • Disconnect the wifi connector on the motherboard.

    Düzenle

  6. Lenovo Yoga Tab 3 10 Motherboard Replacement: adım 5, 2 resimden 1. Lenovo Yoga Tab 3 10 Motherboard Replacement: adım 5, 2 resimden 2.

    • Use the spudger to lift the two speakers up from the small adhesive strip.

    • Place the spudger in the upper left corner of the motherboard and lift it to separate it from the adhesive strip under it.

    • Lift away the motherboard.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

13 farklı kişi bu kılavuzu tamamladı.

Yazar

4 tane daha katılımcı ile

Phanudej

Üyelik tarihi: 02/20/17

1.184 İtibar

5 adet Kılavuz yazıldı

Rozetler: 12

+9 tane daha rozet

Ekip

USF Tampa, Team S3-G2, Sullivan Spring 2017 USF Tampa, Team S3-G2, Sullivan Spring 2017 üyesi

USFT-SULLIVAN-S17S3G2

4 Üyeler

18 adet Kılavuz yazıldı

Bir Yorum

Dear @phanudej ,

I liked your post. I’d have a remark and a question. I made a mistake during the maintanance; with wich I killed a part of the MOBO. So dear users my advice if you want to connect the LCD connector remove the battery before… I had never this issue but now happened. (the device was switched off)

Could you please take a photo of the powerstage of the LCD (I think it should be that) So between the inductor (100; 10uH coil) and an capacity there is a component I do not know what is it (it smoked away) I assume it is a diode…?! They are in the white rectangle near the LCD connector

Thanks in advance

Best regards

@harrincourt

Jozsef Szlatki - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 6

Son 30 gün: 46

Her zaman: 9,153