Ana içeriğe geç

Giriş

If the pedals on your G27 aren't pressing down correctly, or if they just don't feel comfortable under your feet, you will want to replace the springs in the pedals. This isn't a hard replacement to do, all you need is a screwdriver.

Parçalar

Hiçbir parça belirtilmedi.

  1. Remove two screws from each pedal with a 2.5mm allen wrench.
    • Remove two screws from each pedal with a 2.5mm allen wrench.

    • The left two pedals have 30 mm screws and the right-most pedal has 16.3 mm screws.

    • Once these screws are off, take off the front faces on each pedal, they should be very easy to remove.

  2. Flip over the device. Now remove fourteen 15.8 mm screws from the underside of the pedal assembly with a Phillips #1 screwdriver. There are two of these screws under the carpet grip, make sure you don't miss those!
    • Flip over the device. Now remove fourteen 15.8 mm screws from the underside of the pedal assembly with a Phillips #1 screwdriver.

    • There are two of these screws under the carpet grip, make sure you don't miss those!

    • When finished, flip over the device again so that it's in its original position.

  3. Lift the top cover of the device from the front, don't completely remove it yet though, because there are still wires connecting both halves. (NEED PICTURE) Behind the left-most pedal, there are two 7.4mm screws attaching a wire to the top cover. Remove these with a Phillips #1 screwdriver and release the wires. Once the wires are no longer connected to the top cover, remove the cover completely.
    • Lift the top cover of the device from the front, don't completely remove it yet though, because there are still wires connecting both halves. (NEED PICTURE)

    • Behind the left-most pedal, there are two 7.4mm screws attaching a wire to the top cover. Remove these with a Phillips #1 screwdriver and release the wires.

    • Once the wires are no longer connected to the top cover, remove the cover completely.

  4. Simultaneously remove the 10mm screws connecting the pedal to the red piston behind it. This will take two 2.5mm allen wrenches, one for each side of the screw.
    • Simultaneously remove the 10mm screws connecting the pedal to the red piston behind it.

    • This will take two 2.5mm allen wrenches, one for each side of the screw.

    • Once removed, the piston can rotate free of the pedal.

  5. Flip the piston away from the pedal and remove the top half of it. The spring should now be visible. (NEED PICTURE)
    • Flip the piston away from the pedal and remove the top half of it. The spring should now be visible. (NEED PICTURE)

    • Take out the spring, and replace it with a new one.

    • Repeat steps four and five for each pedal that needs a spring replaced.

Sonuç

To reassemble your device, follow these instructions in reverse order.

7 farklı kişi bu kılavuzu tamamladı.

Grant Blake

Üyelik tarihi: 21-04-2015

1.276 İtibar

2 adet Kılavuz yazıldı

Takım

Cal Poly, Team 15-4, Amido Spring 2015 Cal Poly, Team 15-4, Amido Spring 2015 üyesi

CPSU-AMIDO-S15S15G4

4 Üyeler

6 adet Kılavuz yazıldı

3 Yorum

Is it possible to replace / renew the potentiometers used for gas / brake?

Dave Pawson - Yanıt

I replaced the springs and reassembled in reverse order. However, my wheel will no longer power on. Any idea where I would have lost power? Thank you.

matthew.liam.gleason - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 6

Son 7 Gün: 46

Son 30 Gün: 155

Her zaman: 7,500