Eşyalarını Tamir Et Topluluk Mağaza

Logitech VX Nano Wireless Mouse Opening Procedure

Salt Önkoşul
Bu kılavuz yalnızca diğer kılavuzlar için bir ön koşul olarak kullanılmak üzere tasarlanmıştır. Tek başına eksiktir.

Giriş

Prerequisite only guide to open the Logitech VX Nano Wireless Mouse.

Neye ihtiyacın var

  1. Logitech VX Nano Wireless Mouse Opening Procedure, Remove batteries and nano receiver: adım 1, 2 resimden 1. Logitech VX Nano Wireless Mouse Opening Procedure, Remove batteries and nano receiver: adım 1, 2 resimden 2.

    • Pull down on the battery release tab to remove the battery cover.

    • Remove battery cover.

    Düzenle

  2. Logitech VX Nano Wireless Mouse Opening Procedure: adım 2, 2 resimden 1. Logitech VX Nano Wireless Mouse Opening Procedure: adım 2, 2 resimden 2.

    • Pull the battery release tab away from the mouse so the two AA batteries come out.

    Düzenle

  3. Logitech VX Nano Wireless Mouse Opening Procedure: adım 3, 1 resimden 1.

    • If the Nano Receiver is still in the mouse and not in your computer, remove it by pushing on the bright orange button. It should pop right out!

    Düzenle

  5. Logitech VX Nano Wireless Mouse Opening Procedure, Open the mouse: adım 4, 1 resimden 1.

    • Find and remove the screws at the bottom of the battery compartment:

    • Two 6 mm Phillips #1 screws

    • When removing these two screws, it can be helpful to hold the plastic battery tab out of the way of your screwdriver.

    Düzenle

  6. Logitech VX Nano Wireless Mouse Opening Procedure: adım 5, 2 resimden 1. Logitech VX Nano Wireless Mouse Opening Procedure: adım 5, 2 resimden 2.

    • Use an opening pick to get underneath the corner of one of the adhesive skates.

    • As you start to remove the skate, make sure that the opening pick is underneath the entire adhesive pad—otherwise you run the risk of splitting the pad in half.

    • Continue to push the opening pick between the adhesive and the mouse case, slowly working the adhesive away from the case.

    • Repeat this same process for the two other skates.

    • Remove any old adhesive residue before applying new mouse skates.

    Düzenle

  7. Logitech VX Nano Wireless Mouse Opening Procedure: adım 6, 1 resimden 1.

    • Remove the screws from the backside of the mouse:

    • Three 6 mm Phillips #1 screws

    • The top shell and bottom case are no longer connected. Keep the mouse steady so you can carefully remove the upper shell in the next step.

    Düzenle

  8. Logitech VX Nano Wireless Mouse Opening Procedure: adım 7, 2 resimden 1. Logitech VX Nano Wireless Mouse Opening Procedure: adım 7, 2 resimden 2.

    • Carefully separate the top plastic shell from the bottom case.

    • Remove the top shell.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

Carsten Frauenheim

Üyelik tarihi: 03/10/20

112.881 İtibar

338 adet Kılavuz yazıldı

Rozetler: 40

+37 tane daha rozet

Ekip

iFixit iFixit üyesi

Staff

135 Üyeler

16.732 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 0

Her zaman: 38