Eşyalarını Tamir Et

Onarma Hakkı

Mağaza

MacBook Core Duo LCD Assembly Replacement

Yazan: Andrew Bookholt (ve 4 başka katılımcı)
  • Yorumlar: 4
  • Favoriler: 0

Zorluk

Orta

Adımlar

9

Gerekli Süre

Bir süre öner??

Bölümler

1

İşaretler

1

Prerequisite Only

Salt Önkoşul

Bu kılavuzun yalnızca diğer kılavuzlar için bir önkoşul kılavuzu olduğunu lütfen dikkate alın.

Giriş

Internal Prerequisite.

Aletler

Bu aletleri satın al

Parçalar

Hiçbir parça belirtilmedi.

  1. Remove the small piece of foam tape stuck down above each of the bezel covers. Remove the small piece of foam tape stuck down above each of the bezel covers.

    • Remove the small piece of foam tape stuck down above each of the bezel covers.

    Düzenle

  2. Use a spudger to slide the left bezel cover towards the LCD panel. Do not lift up vertically on the cover! Unlike the large display bezel, this one has horizontal hooks to keep it in place. These will break easily.

    • Use a spudger to slide the left bezel cover towards the LCD panel.

    • Do not lift up vertically on the cover! Unlike the large display bezel, this one has horizontal hooks to keep it in place. These will break easily.

    • Lift the left bezel cover off the display assembly.

    Düzenle

  3. Use a spudger to slide the right bezel cover toward the LCD panel. Lift the right bezel cover off the display assembly.

    • Use a spudger to slide the right bezel cover toward the LCD panel.

    • Lift the right bezel cover off the display assembly.

    Düzenle

  5. Lift the inverter out of the display slightly and disconnect the backlight cable from its right side. Place the inverter back down in its recess.

    • Lift the inverter out of the display slightly and disconnect the backlight cable from its right side.

    • Place the inverter back down in its recess.

    Düzenle

  6. Remove the single 3.2 mm Phillips screw securing the display data cable to the right clutch hinge.

    • Remove the single 3.2 mm Phillips screw securing the display data cable to the right clutch hinge.

    Düzenle

  7. Move the display data cable out from under the mounting arm of the right clutch hinge.

    • Move the display data cable out from under the mounting arm of the right clutch hinge.

    Düzenle

  8. Remove the twelve 4.2 mm Phillips screws securing the LCD assembly to the rear display bezel.

    • Remove the twelve 4.2 mm Phillips screws securing the LCD assembly to the rear display bezel.

    • Make sure you pay attention to how the microphone cable (and antenna cable on some models) are routed around the outside of the two screws nearest to the bottom of the screen (on both left and right). It's easy to damage the cables if not routed properly when putting these screws back on.

    Düzenle

  9. Lift the LCD assembly out of the rear display bezel, minding any cables that may get caught.

    • Lift the LCD assembly out of the rear display bezel, minding any cables that may get caught.

    Düzenle

  10. Be sure to keep track of the small magnet along the left side of the display. It may be stuck to the LCD frames or to the rear display bezel. When installing it, be sure short side is facing upward.

    • Be sure to keep track of the small magnet along the left side of the display. It may be stuck to the LCD frames or to the rear display bezel. When installing it, be sure short side is facing upward.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

0 Yorum

Yorum Ekle

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 3

Her zaman: 404