Eşyalarını Tamir Et Topluluk Mağaza

MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement

Salt Önkoşul
Bu kılavuz yalnızca diğer kılavuzlar için bir ön koşul olarak kullanılmak üzere tasarlanmıştır. Tek başına eksiktir.

Neye ihtiyacın var

  1. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement, Trackpad Cable: adım 1, 2 resimden 1. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement, Trackpad Cable: adım 1, 2 resimden 2.

    • Use the flat end of a spudger to pop the trackpad connector straight up off its socket on the logic board.

    Düzenle

  2. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: adım 2, 2 resimden 1. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: adım 2, 2 resimden 2.

    • Lift the trackpad cable up off the battery to separate it from the adhesive securing it.

    • Be careful not to damage the cable. If it doesn't peel up easily, apply a little heat from an iOpener, heat gun, or hair dryer to soften the adhesive, and try again.

    • If you are installing a new trackpad cable, be sure to fold the new cable to match the shape of the old cable. The new cable will appear to be too long if it is not folded.

    Düzenle

  4. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: adım 3, 3 resimden 1. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: adım 3, 3 resimden 2. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: adım 3, 3 resimden 3.

    • If necessary, peel back any tape covering the trackpad cable connector.

    • Use the end of a spudger to flip the retaining tab on the ZIF connector.

    Düzenle

  5. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: adım 4, 2 resimden 1. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: adım 4, 2 resimden 2.

    • Pull the trackpad cable straight out of its ZIF socket on the trackpad control board.

    • During reassembly, make sure that the retaining tab is in the up, "unlocked" position before you insert the cable into the socket.

    Düzenle

  6. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: adım 5, 1 resimden 1.

    • Remove the single 3.7 mm T5 Torx screw securing the battery board to the upper case.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

3 farklı kişi bu kılavuzu tamamladı.

Yazar

6 tane daha katılımcı ile

Sam Goldheart

Üyelik tarihi: 10/18/12

471.892 İtibar

538 adet Kılavuz yazıldı

Rozetler: 48

+45 tane daha rozet

Ekip

iFixit iFixit üyesi

Staff

118 Üyeler

19.656 adet Kılavuz yazıldı

3Kılavuz Yorumları

Why remove the screw in step 5?

Ari Cooper - Davis - Yanıt

Yes @sam , why should you remove the screw in step 5? Is this a mistake?

lmdehaas - Yanıt

Step 5: Remove the single 3.7 mm T5 Torx screw.

Step 6: Re-screw single 3.7 mm T5 Torx screw.

David Grabowski - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 15

Her zaman: 1,814