Giriş

This guide will show how to open up the PowerBook so that you may access the hard drive, and then show how to remove the hard drive.

Turn the device upside down and then locate the battery latch near the front of the device.
  • Turn the device upside down and then locate the battery latch near the front of the device.

Yorum Ekle

Slide the latch to the left to release the battery.
  • Slide the latch to the left to release the battery.

Yorum Ekle

  • Continue holding the latch then gently pull the battery out of the device.

  • Place the battery in a safe location.

Yorum Ekle

  • Locate the CD-ROM Drive latch.

Yorum Ekle

  • Slide the latch to the right to release the CD ROM drive.

Yorum Ekle

  • Continue holding the latch then gently pull the CD-ROM Drive out of the device.

  • Place the CD ROM drive in a safe location.

Yorum Ekle

  • Locate the speaker cover.

Yorum Ekle

  • Press firmly on each end of the speaker cover and slide it to the left.

I found it was easy to get a spudger over the left edge and lift it up a bit, then push the bar to the left, It pops right off after that.

Jimmy James - Yanıt

  • Gently lift the speaker cover to remove it.

Yorum Ekle

  • Lift the keyboard up from the back using a spudger(wedge side).

Yorum Ekle

  • Gently lift the keyboard until only the ribbon cable remains attached.

Yorum Ekle

  • Tilt the keyboard away from the screen.

Yorum Ekle

  • Locate the six screws that secure the heatsink.

This is not necessary to remove the HDD. Go directly to step 20.

Kenneth DeVries - Yanıt

That isn't the HDD!

Dix Dox - Yanıt

  • Remove the six screws from the heatsink using the Philips #1 screwdriver.

Yorum Ekle

  • Lift the heatsink from the side closest to the laptop screen.

Yorum Ekle

  • Remove the heatsink.

Yorum Ekle

  • Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.

Yorum Ekle

  • Detach the ribbon cable.

Yorum Ekle

  • Remove the keyboard.

Yorum Ekle

  • Locate and identify the two screws that attach the hard drive to the computer.

Yorum Ekle

  • Remove the screws with a Phillips #0 screwdriver.

Yorum Ekle

  • Once the screws are removed, lift up the end of the hard drive using your finger tips.

Yorum Ekle

  • Fully lift the hard drive vertically against the side of the computer.

Yorum Ekle

  • Push a finger down onto the plastic strap.

Yorum Ekle

  • Remove the hard drive from the computer by pushing down on the plastic strap and pulling up on the hard drive.

Yorum Ekle

  • The hard drive is now separated from the computer.

Yorum Ekle

  • Reverse these instructions to install a new hard drive, or to put the computer back together.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

5 başka kişi bu kılavuzu tamamladı.

Jeffrey Huntley

Üyelik tarihi: 01-04-2011

122 İtibar

1 Kılavuz yazıldı

Takım

Cal Poly, Team 10-39, Forte Spring 2011 Cal Poly, Team 10-39, Forte Spring 2011 üyesi

CPSU-FORTE-S11S10G39

5 Üyeler

6 adet Kılavuz yazıldı

Bir Yorum

Hi iFixIt thanks for all the details BUT the keyboard can indeed stay in

when changing the hard drive. Just slide it a bit to the right after step

11, the ribbon cble does not take any damage. SO: from step 12 jump

straight to step 20. The heat sink can stay untouched, which i find not

unimportant to mention. Regards, TB75

TB75 - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 4

Son 30 Gün: 26

Her zaman: 5,893