Giriş

The keyboard has 3 main parts, including the speaker cover, the heat sink, and the keyboard itself. You have to remove these in order to remove the keyboard.

Parçalar

Hiçbir parçaya gerek yok.

Turn the device upside down and then locate the battery latch near the front of the device.
  • Turn the device upside down and then locate the battery latch near the front of the device.

Yorum Ekle

Slide the latch to the left to release the battery.
  • Slide the latch to the left to release the battery.

Yorum Ekle

Continue holding the latch then gently pull the battery out of the device.
  • Continue holding the latch then gently pull the battery out of the device.

  • Place the battery in a safe location.

Yorum Ekle

Locate the CD-ROM Drive latch.
  • Locate the CD-ROM Drive latch.

Yorum Ekle

Slide the latch to the right to release the CD ROM drive.
  • Slide the latch to the right to release the CD ROM drive.

Yorum Ekle

Continue holding the latch then gently pull the CD-ROM Drive out of the device.
  • Continue holding the latch then gently pull the CD-ROM Drive out of the device.

  • Place the CD ROM drive in a safe location.

Yorum Ekle

Locate the speaker cover.
  • Locate the speaker cover.

Yorum Ekle

Press firmly on each end of the speaker cover and slide it to the left.
  • Press firmly on each end of the speaker cover and slide it to the left.

I found it was easy to get a spudger over the left edge and lift it up a bit, then push the bar to the left, It pops right off after that.

Jimmy James - Yanıt

Gently lift the speaker cover to remove it.
  • Gently lift the speaker cover to remove it.

Yorum Ekle

Lift the keyboard up from the back using a spudger(wedge side).
  • Lift the keyboard up from the back using a spudger(wedge side).

Yorum Ekle

Gently lift the keyboard until only the ribbon cable remains attached.
  • Gently lift the keyboard until only the ribbon cable remains attached.

Yorum Ekle

Tilt the keyboard away from the screen.
  • Tilt the keyboard away from the screen.

Yorum Ekle

Locate the six screws that secure the heatsink.
  • Locate the six screws that secure the heatsink.

This is not necessary to remove the HDD. Go directly to step 20.

Kenneth DeVries - Yanıt

That isn't the HDD!

Dix Dox - Yanıt

Remove the six screws from the heatsink using the Philips #1 screwdriver.
  • Remove the six screws from the heatsink using the Philips #1 screwdriver.

Yorum Ekle

Lift the heatsink from the side closest to the laptop screen.
  • Lift the heatsink from the side closest to the laptop screen.

Yorum Ekle

Remove the heatsink.
  • Remove the heatsink.

Yorum Ekle

Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.
  • Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.

Yorum Ekle

Detach the ribbon cable.
  • Detach the ribbon cable.

Yorum Ekle

Remove the keyboard.
  • Remove the keyboard.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

Bir başkası bu kılavuzu tamamladı.

Sean Bent

Üyelik tarihi: 01-04-2011

41 İtibar

1 Kılavuz yazıldı

Takım

Cal Poly, Team 10-39, Forte Spring 2011 Cal Poly, Team 10-39, Forte Spring 2011 üyesi

CPSU-FORTE-S11S10G39

5 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 0

Son 30 Gün: 1

Tüm Zamanlar: 1,812