Eşyalarını Tamir Et Topluluk Mağaza

Magellan RoadMate 1440 Screen Replacement

Giriş

After removing the back cover and battery, follow this guide in order to remove the screen from the device.

Neye ihtiyacın var

  1. Magellan RoadMate 1440 Screen Replacement, Magellan RoadMate 1440 Back Cover Disassembly: adım 1, 1 resimden 1.

    • Place the GPS with the screen facing down.

    Düzenle

  2. Magellan RoadMate 1440 Screen Replacement: adım 2, 2 resimden 1. Magellan RoadMate 1440 Screen Replacement: adım 2, 2 resimden 2.

    • Remove the four 4.2 mm screws on the back cover of the device using a Phillips #0 screwdriver.

    Düzenle

  3. Magellan RoadMate 1440 Screen Replacement: adım 3, 2 resimden 1. Magellan RoadMate 1440 Screen Replacement: adım 3, 2 resimden 2.

    • Remove the two 4.2mm screws at the bottom of the device using a Phillips #0 screwdriver.

    Düzenle

  4. Magellan RoadMate 1440 Screen Replacement: adım 4, 3 resimden 1. Magellan RoadMate 1440 Screen Replacement: adım 4, 3 resimden 2. Magellan RoadMate 1440 Screen Replacement: adım 4, 3 resimden 3.

    • Insert the black spudger into the crease in the side of the GPS.

    • Move the end of the spudger down to break the seal between the two plastic shells.

    • Continue doing this along each side of the GPS to ensure a smooth removal.

    Düzenle

  6. Magellan RoadMate 1440 Screen Replacement: adım 5, 3 resimden 1. Magellan RoadMate 1440 Screen Replacement: adım 5, 3 resimden 2. Magellan RoadMate 1440 Screen Replacement: adım 5, 3 resimden 3.

    • Fully separate the two sides of the case.

    • Remove the tape on the battery wires and the tape on the speaker wires.

    Düzenle

  7. Magellan RoadMate 1440 Screen Replacement, Battery: adım 6, 2 resimden 1. Magellan RoadMate 1440 Screen Replacement, Battery: adım 6, 2 resimden 2.

    • Use the black spudger to break the seal between the adhesive and battery. Use the same spudger to continue to pry the battery from the backing

    • This may be a little tough to separate the battery and the adhesive

    Düzenle

  8. Magellan RoadMate 1440 Screen Replacement: adım 7, 2 resimden 1. Magellan RoadMate 1440 Screen Replacement: adım 7, 2 resimden 2.

    • Lift the battery from the device

    • Once the battery is free from the adhesive, remove the piece of tape with a pair of tweezers that is covering the connection of the battery to the motherboard.

    Düzenle

  9. Magellan RoadMate 1440 Screen Replacement: adım 8, 2 resimden 1. Magellan RoadMate 1440 Screen Replacement: adım 8, 2 resimden 2.

    • Unplug the battery from the mother board by pulling back the clips and pulling the wires away from the motherboards receptacle

    • It is important for your and the device's safety to remove the battery before continuing with any other part removals.

    • It is not necessary to separate the red and white wires from the battery. A replacement battery pack will come with similar wires already attached.

    Düzenle

  10. Magellan RoadMate 1440 Screen Replacement, Screen: adım 9, 1 resimden 1.

    • Replace the device's screen.

    Düzenle

  11. Magellan RoadMate 1440 Screen Replacement: adım 10, 3 resimden 1. Magellan RoadMate 1440 Screen Replacement: adım 10, 3 resimden 2. Magellan RoadMate 1440 Screen Replacement: adım 10, 3 resimden 3.

    • It may be necessary to get help from a friend to hold the device stable while removing the screen.

    • Using two hands, pull back the tabs holding the screen in place.

    • Use a spudger to help use leverage to remove the screen, if necessary

    Düzenle

  12. Magellan RoadMate 1440 Screen Replacement: adım 11, 2 resimden 1. Magellan RoadMate 1440 Screen Replacement: adım 11, 2 resimden 2.

    • Raise the switch locking the ribbon cable in place.

    • Using twesers, pull the ribbon cable from the socket.

    Düzenle

  13. Magellan RoadMate 1440 Screen Replacement: adım 12, 2 resimden 1. Magellan RoadMate 1440 Screen Replacement: adım 12, 2 resimden 2.

    • With the ribbon cable removed, the screen is completely disconnected from the device.

    • To replace the ribbon cable, press the two tabs to push the head into the socket.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

1 tane daha katılımcı ile

Miller Hall

Üyelik tarihi: 03/21/16

325 İtibar

2 adet Kılavuz yazıldı

Rozetler: 8

+5 tane daha rozet

Ekip

Clemson, Team 7-3, Benson Spring 2016 Clemson, Team 7-3, Benson Spring 2016 üyesi

CLEM-BENSON-S16S7G3

4 Üyeler

7 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 1

Her zaman: 404