Eşyalarını Tamir Et Topluluk Mağaza

Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement

Giriş

How to remove the cutting head for replacement or further device service in a Mk Diamond Wet Saw MK660 2010.

  1. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement, Blade Cover: adım 1, 3 resimden 1. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement, Blade Cover: adım 1, 3 resimden 2. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement, Blade Cover: adım 1, 3 resimden 3.

    • Before you begin, make sure to power off and unplug the device from the outlet.

    • If the clear water pump hose is connected, remove it now.

    • Loosen the plastic knob holding the saw's cutting head in place.

    • Lower the cutting head while keeping it steady.

    Düzenle

  2. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement: adım 2, 2 resimden 1. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement: adım 2, 2 resimden 2.

    • Unscrew the knob.

    • Remove it from the cutting head.

    Düzenle

  3. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement: adım 3, 2 resimden 1. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement: adım 3, 2 resimden 2.

    • Loosen the plastic knob holding the blade cover in place.

    Düzenle

  5. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement: adım 4, 3 resimden 1. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement: adım 4, 3 resimden 2. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement: adım 4, 3 resimden 3.

    • Loosen the wing nut on the blade cover pivot shaft.

    • Remove the wing nut and accompanying washer.

    Düzenle

  6. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement: adım 5, 2 resimden 1. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement: adım 5, 2 resimden 2.

    • Pivot the blade cover up and pull it off the shaft.

    Düzenle

  7. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement, Blade: adım 6, 3 resimden 1. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement, Blade: adım 6, 3 resimden 2. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement, Blade: adım 6, 3 resimden 3.

    • Insert the provided spanner wrench into one of the four tightening holes on the inner flange behind the blade.

    • Use the the provided nut wrench to loosen the hex nut while providing counterforce with the spanner wrench.

    Düzenle

  8. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement: adım 7, 2 resimden 1. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement: adım 7, 2 resimden 2.

    • Remove the hex nut.

    • Remove the outer flange.

    Düzenle

  9. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement: adım 8, 2 resimden 1. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement: adım 8, 2 resimden 2.

    • Remove the cutting blade.

    • The blade can be sharp, so handle with care.

    Düzenle

  10. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement, Cutting Head: adım 9, 3 resimden 1. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement, Cutting Head: adım 9, 3 resimden 2. Mk Diamond Wet Saws MK660 2010 Cutting Head Replacement, Cutting Head: adım 9, 3 resimden 3.

    • Pull the entire cutting head straight off the shaft holding it in place.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

Carsten Frauenheim

Üyelik tarihi: 03/10/20

112.881 İtibar

338 adet Kılavuz yazıldı

Rozetler: 40

+37 tane daha rozet

Ekip

iFixit iFixit üyesi

Staff

135 Üyeler

16.732 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 2

Her zaman: 120