Giriş

If no other troubleshooting tips help, it may be time to install a new motherboard. This installation guide will walk the reader through the steps required in replacing the motherboard.

  1. Locate the power button at the top of the phone.  Depress power button for 2 seconds until a menu appears.
    • Locate the power button at the top of the phone. Depress power button for 2 seconds until a menu appears.

    Yorum Ekle

  2. Once the menu appears, select the "power off" option.  Wait until the phone is completely off.
    • Once the menu appears, select the "power off" option. Wait until the phone is completely off.

    Yorum Ekle

    • Place thumb on the back cover, and push down towards the bottom of the device. Once the cover releases, pull it away from the phone and set it aside.

    Yorum Ekle

    • Find the yellow pull tab located in the upper left corner. Pull the tab until the battery dislodges. Grab the battery by the raised edge, and remove it from the case.

    Yorum Ekle

    • The battery has been successfully removed.

    Yorum Ekle

    • Remove the micro SD card from its connector.

    Yorum Ekle

    • Locate the seam between the back case and the end cover on the top edge of the phone.

    • Use the plastic opening tool to detach the two clips by wedging the tool into the right side of the seam and moving right to left. Once the cover comes off set it aside

    Yorum Ekle

    • Repeat step 2 on the bottom cover.

    Yorum Ekle

    • Use a T5 Torx screwdriver to remove the screws in each corner of the phone.

    • The screws are very small so make sure not to lose them.

    Yorum Ekle

    • Flip the phone over and locate the screw on the middle of the left side. Unscrew it using the T5 Torx screwdriver and set it aside.

    Yorum Ekle

    • Identify the screw located in the bottom right corner of the battery case. Remove the screw with a T5 (or in some cases T6) torx screwdriver and set it aside.

    Yorum Ekle

    • Locate the seam along the right edge of the phone. Use the prying tool to disconnect the two clips along the edge.

    Yorum Ekle

    • Locate the two clips on the inside of the case and use the spudger tool to detach them from the case. To detach each clip, use the sharp end to press the small, black plastic in the center of the clip.

    Yorum Ekle

    • After the clips are detached, remove the back case and set it aside.

    Yorum Ekle

    • Remove the screws along both sides of the motherboard using a T3 Torx screwdriver. On some phones this may require a #1 Phillips Screw Driver.

    These are T3 screws. I have taken apart about 15 of them in the past week, T4 is too big to fit. Had to use a T3 bit to remove them.

    Christopher Moody - Yanıt

    These screws are T4 on my phone, not T3. I stripped 2 screws trying to remove them with T3. Maybe it could be either.

    Jim Cooper - Yanıt

    On my phone all screws from Step 15 - 29 were actually #0 Phillip head.

    Peter Merl - Yanıt

    • Carefully remove the white connecting wire from the motherboard using tweezers.

    • Use caution, this wire is delicate.

    Yorum Ekle

    • Scrape away the electrical tape that covers the LCD and digitizer cable using the spudger tool or a fingernail.

    Yorum Ekle

    • Use the spudger tool to pop the Digitizer cable off of the motherboard.

    Yorum Ekle

    • Carefully flip the small white connector up and away from the motherboard.

    Yorum Ekle

    • Gently pull the flat gold cable out from the connector.

    Yorum Ekle

    • Carefully lift the motherboard and camera module up. Do not remove it from the phone!

    Yorum Ekle

    • Using the spudger tool, pop the black cable connector off of the motherboard.

    Yorum Ekle

    • It is to safe remove the motherboard from the phone.

    Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

Bir başkası bu kılavuzu tamamladı.

Sam Johnston

Üyelik tarihi: 03-10-2012

486 İtibar

4 adet Kılavuz yazıldı

Takım

Cal Poly, Team 18-40, Regan Fall 2012 Cal Poly, Team 18-40, Regan Fall 2012 üyesi

CPSU-REGAN-F12S18G40

3 Üyeler

5 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 Gün: 1

Son 30 Gün: 3

Her zaman: 3,496