Eşyalarını Tamir Et Topluluk Mağaza

Motorola MBP667CONNECT Speaker Replacement

Giriş

This guide will show users how to take apart the camera housing in order to replace the speaker.

Neye ihtiyacın var

  1. Motorola MBP667CONNECT Speaker Replacement, Camera Stand: adım 1, 2 resimden 1. Motorola MBP667CONNECT Speaker Replacement, Camera Stand: adım 1, 2 resimden 2.

    • Remove two 5 mm Phillips #1 screws from the bottom of the camera stand.

    Düzenle

  2. Motorola MBP667CONNECT Speaker Replacement: adım 2, 1 resimden 1.

    • Use a nylon spudger to remove the casing.

    Düzenle

  3. Motorola MBP667CONNECT Speaker Replacement: adım 3, 1 resimden 1.

    • Remove the two 5 mm Phillips #1 screws attached to the black plastic under the casing.

    Düzenle

  5. Motorola MBP667CONNECT Speaker Replacement: adım 4, 2 resimden 1. Motorola MBP667CONNECT Speaker Replacement: adım 4, 2 resimden 2.

    • Remove the black circular plastic part.

    Düzenle

  6. Motorola MBP667CONNECT Speaker Replacement: adım 5, 1 resimden 1.

    • Remove the white plastic wire housing beneath the black plastic.

    Düzenle

  7. Motorola MBP667CONNECT Speaker Replacement: adım 6, 2 resimden 1. Motorola MBP667CONNECT Speaker Replacement: adım 6, 2 resimden 2.

    • Now, remove the bottom of the stand by pulling it from the camera.

    Düzenle

  8. Motorola MBP667CONNECT Speaker Replacement, Speaker: adım 7, 3 resimden 1. Motorola MBP667CONNECT Speaker Replacement, Speaker: adım 7, 3 resimden 2. Motorola MBP667CONNECT Speaker Replacement, Speaker: adım 7, 3 resimden 3.

    • Remove the Phillips #1 screws on the back of the device.

    • Use a nylon spudger to remove the casing. This will separate the frontside of the camera from the backside.

    Düzenle

  9. Motorola MBP667CONNECT Speaker Replacement: adım 8, 2 resimden 1. Motorola MBP667CONNECT Speaker Replacement: adım 8, 2 resimden 2.

    • Now locate the brackets by the speaker on the frontside of the camera and use the metal spudger to carefully disconnect from casing.

    • Continue to use the metal spudger to carefully disconnect the remaining brackets from the casing.

    Düzenle

  10. Motorola MBP667CONNECT Speaker Replacement: adım 9, 2 resimden 1. Motorola MBP667CONNECT Speaker Replacement: adım 9, 2 resimden 2.

    • Using the soldering iron, desolder the speaker wires that are attached to the circuit board.

    • Use caution while handling the soldering iron. This tool gets very hot!

    • After desoldering the speaker wires, remove the wires from the circuit board.

    • Thread the wires from the new speaker wires through the holes in the circuit board. Using the soldering iron, re-solder the wires to the circuit board.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

4 tane daha katılımcı ile

Kyle Kramer

Üyelik tarihi: 01/16/19

255 İtibar

2 adet Kılavuz yazıldı

Rozetler: 2

Ekip

Eastern Washington University, Team S1-G6, Crawford Winter 2019 Eastern Washington University, Team S1-G6, Crawford Winter 2019 üyesi

EWU-CRAWFORD-W19S1G6

4 Üyeler

4 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 1

Her zaman: 162