Menü

Ayarlarınız

Tezgahım

Cihazlarınız için kılavuz, parça ve cevaplara hızlı erişim edinin
Sepetim

Sepetiniz boş görünüyor

Mağazamıza Göz Atın

Motorola Razr V3c Motherboard (CDMA) Replacement

Yazan: Joshua Ruehlig (ve 3 başka katılımcı)
  • Yorumlar: 2
  • Favoriler: 5
  • Tamamlanma: 6

Zorluk

Çok kolay

Adımlar

9

Gerekli Süre

10 dakika

Bölümler

3

İşaretler

0

Giriş

This guide will show you how to remove the motherboard on a Motorola V3c.

Aletler

Bu aletleri satın al

Parçalar

Hiçbir parçaya gerek yok.

  1. Press down on the the rear panel release button while simultaneously prying the rear panel straight away from the V3c. Lift and remove the rear panel away from the V3c. Lift and remove the rear panel away from the V3c.

    • Press down on the the rear panel release button while simultaneously prying the rear panel straight away from the V3c.

    • Lift and remove the rear panel away from the V3c.

    Düzenle

  2. Remove the battery by pushing in the top of the battery and lifting it away from the phone. Remove the battery by pushing in the top of the battery and lifting it away from the phone.

    • Remove the battery by pushing in the top of the battery and lifting it away from the phone.

    Düzenle

  3. Unscrew the two screws in the back using the T6.

    • Unscrew the two screws in the back using the T6.

    Düzenle

  4. Pro Tech Toolkit içeren veya $100tüm siparişlerde ücretsiz kargo!

    Mağazamıza Göz Atın

  5. Use the plastic opening tool to pop the bottom and the sides off the back casing.

    • Use the plastic opening tool to pop the bottom and the sides off the back casing.

    • Be careful not to pull the back lower cover off too far as it is connected to the phone body by a ribbon.

    Düzenle

  6. Peel off the connector between the motherboard and the body of the phone.

    • Peel off the connector between the motherboard and the body of the phone.

    Düzenle

  7. Pull out the two black rubber covers using tweezers. The second rubber cover is much harder to get out.

    • Pull out the two black rubber covers using tweezers.

    • The second rubber cover is much harder to get out.

    Düzenle

  8. Pull out the white plastic cover by unclipping the two plastic pieces shown. Pull out the white plastic cover by unclipping the two plastic pieces shown.

    • Pull out the white plastic cover by unclipping the two plastic pieces shown.

    Düzenle

  9. Pull out the speaker.

    • Pull out the speaker.

    Düzenle

  10. Pull out the motherboard. You may also now replace the bottom lower casing

    • Pull out the motherboard.

    • You may also now replace the bottom lower casing

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

6 farklı kişi bu kılavuzu tamamladı.

Yazar

3 tane daha katılımcı ile

Joshua Ruehlig

Üyelik tarihi: 14-01-2010

503 İtibar

4 adet Kılavuz yazıldı

Rozetler: 10

+7 tane daha rozet

Takım

Cal Poly, Team 11-4, Forte Winter 2010 Cal Poly, Team 11-4, Forte Winter 2010 üyesi

CPSU-FORTE-W10S11G4

3 Üyeler

8 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 1

Son 30 Gün: 3

Her zaman: 6,411