Place the monitor face down on a clean, flat surface. Place the monitor face down on a clean, flat surface.
  • Place the monitor face down on a clean, flat surface.

Yorum Ekle

Firmly remove the back panel of the stand by pulling it up and away from the monitor. Firmly remove the back panel of the stand by pulling it up and away from the monitor.
  • Firmly remove the back panel of the stand by pulling it up and away from the monitor.

Yorum Ekle

Unscrew the two 6mm Phillips PH2 screws to detach the stand enclosure from the stand. Unscrew the two 6mm Phillips PH2 screws to detach the stand enclosure from the stand.
  • Unscrew the two 6mm Phillips PH2 screws to detach the stand enclosure from the stand.

Yorum Ekle

Firmly grasp the stand enclosure with your hand and slide it to base of stand. Firmly grasp the stand enclosure with your hand and slide it to base of stand.
  • Firmly grasp the stand enclosure with your hand and slide it to base of stand.

Yorum Ekle

Unscrew the two 14.5mm Phillips PH2 screws holding the stand to the monitor.
  • Unscrew the two 14.5mm Phillips PH2 screws holding the stand to the monitor.

Yorum Ekle

Lift the the stand straight up to remove it. Lift the the stand straight up to remove it.
  • Lift the the stand straight up to remove it.

Yorum Ekle

Place the monitor screen face up. Pull the frame off by placing your fingers on the inside of the frame and pulling out and up, the frame should snap off. Continue your way around the screen.
  • Place the monitor screen face up.

  • Pull the frame off by placing your fingers on the inside of the frame and pulling out and up, the frame should snap off.

  • Continue your way around the screen.

Yorum Ekle

Unscrew the two 7mm screws from the bottom of the button assembly. Do not pull the button assembly out too quickly or with too much force! Damage to the wires can occur. Pull the button assembly out a few inches and unplug the colored cables.
  • Unscrew the two 7mm screws from the bottom of the button assembly.

  • Do not pull the button assembly out too quickly or with too much force! Damage to the wires can occur.

  • Pull the button assembly out a few inches and unplug the colored cables.

Yorum Ekle

Unscrew the gold colored 7mm Phillips PH000 screw holding the button assembly to the monitor. Remove the button assembly from the monitor.
  • Unscrew the gold colored 7mm Phillips PH000 screw holding the button assembly to the monitor.

  • Remove the button assembly from the monitor.

Yorum Ekle

With the monitor face-down, unscrew the 5 7mm Phillips PH2 screws around the outside of the enclosure.
  • With the monitor face-down, unscrew the 5 7mm Phillips PH2 screws around the outside of the enclosure.

Yorum Ekle

Unscrew the 2 14.5mm Phillips PH2 screws located on the raised center of the enclosure. Carefully pull the enclosure off the monitor. Carefully pull the enclosure off the monitor.
  • Unscrew the 2 14.5mm Phillips PH2 screws located on the raised center of the enclosure.

  • Carefully pull the enclosure off the monitor.

Yorum Ekle

Unscrew the 10 5mm Philips PH2 screws holding the metal casing to the monitor. Unscrew the 10 5mm Philips PH2 screws holding the metal casing to the monitor.
  • Unscrew the 10 5mm Philips PH2 screws holding the metal casing to the monitor.

Yorum Ekle

Pull  the the metal casing off of the monitor to reveal the motherboards. Pull  the the metal casing off of the monitor to reveal the motherboards.
  • Pull the the metal casing off of the monitor to reveal the motherboards.

Yorum Ekle

Carefully insert the prying tool underneath the power supply fuse. Using the prying tool, lift the power supply fuse out of its emplacement until it is resting on its clamps.
  • Carefully insert the prying tool underneath the power supply fuse.

  • Using the prying tool, lift the power supply fuse out of its emplacement until it is resting on its clamps.

Yorum Ekle

Carefully remove the power supply fuse by hand.
  • Carefully remove the power supply fuse by hand.

Yorum Ekle

Place the replacement power supply fuse on the fuse clips. With a finger, press down on the ends of the replacement fuse until it is properly seated in the fuse clips. With a finger, press down on the ends of the replacement fuse until it is properly seated in the fuse clips.
  • Place the replacement power supply fuse on the fuse clips.

  • With a finger, press down on the ends of the replacement fuse until it is properly seated in the fuse clips.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

Drew Troxell

Üyelik tarihi: 18-10-2013

113 İtibar

1 Kılavuz yazıldı

Takım

Cal Poly, Team 11-36, Amido Fall 2013 Cal Poly, Team 11-36, Amido Fall 2013 üyesi

CPSU-AMIDO-F13S11G36

5 Üyeler

7 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 0

Son 30 Gün: 2

Tüm Zamanlar: 415