Giriş

A broken plunger may prevent your rifle from firing. This guide shows you how to replace the plunger.

Parçalar

Hiçbir parçaya gerek yok.

There are many screws of varying lengths involved in the disassembling of this device. It is important to keep track which screws correspond to which holes. This will help ensure proper reassembly.
  • There are many screws of varying lengths involved in the disassembling of this device. It is important to keep track which screws correspond to which holes. This will help ensure proper reassembly.

  • Be sure that the rifle is discharged and unloaded before starting disassembly.

Yorum Ekle

Looking from the rear of the rifle, remove the two 10 mm phillips screws holding the orange cap to the butt of the rifle. Pull off the orange cap. Pull off the orange cap.
  • Looking from the rear of the rifle, remove the two 10 mm phillips screws holding the orange cap to the butt of the rifle.

  • Pull off the orange cap.

Yorum Ekle

With the rifle barrel pointing left, remove the two 8mm phillips screws holding the slide mechanism together. Remove the three 10 mm phillips screws from the bottom of the slide mechanism. Separate and remove the two halves of the slide mechanism.
  • With the rifle barrel pointing left, remove the two 8mm phillips screws holding the slide mechanism together.

  • Remove the three 10 mm phillips screws from the bottom of the slide mechanism.

  • Separate and remove the two halves of the slide mechanism.

  • Make sure to keep track of which screws correspond to which holes.

Yorum Ekle

Again with the rifle barrel pointing left, remove the fourteen 10 mm phillips screws from the main body of the rifle. Remove the two 5 mm phillips screws from the main body.
  • Again with the rifle barrel pointing left, remove the fourteen 10 mm phillips screws from the main body of the rifle.

  • Remove the two 5 mm phillips screws from the main body.

  • Remove the two 8 mm phillips screws from the main body.

  • Screws are varying lengths, make sure to keep track of which screws correspond to which holes.

The screw to the left of the orange Nerf logo is actually 8mm, not 10 mm indicated in the key.

Nikolas Hill - Yanıt

Pull the two halves of the rifle apart. Be careful of the spring at the rear end of the rifle. It may come flying out. If you have difficulty pulling the two halves apart, spudger to gently pry the edges of the body apart.
  • Pull the two halves of the rifle apart.

  • Be careful of the spring at the rear end of the rifle. It may come flying out.

  • If you have difficulty pulling the two halves apart, spudger to gently pry the edges of the body apart.

  • Also be careful of small parts when opening the gun, they may be easy to lose.

  • Remove the access gate and barrel cover.

Yorum Ekle

You should now be able to pull the main firing spring from the rear of the rifle.
  • You should now be able to pull the main firing spring from the rear of the rifle.

Yorum Ekle

Slide the plunger lock rearwards and towards yourself to lift it out.
  • Slide the plunger lock rearwards and towards yourself to lift it out.

Yorum Ekle

Pull the plunger towards the rear of the rifle to remove it.
  • Pull the plunger towards the rear of the rifle to remove it.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

Elizabeth Coffey

Üyelik tarihi: 26-01-2014

377 İtibar

3 adet Kılavuz yazıldı

Takım

Cal Poly, Team 10-35, Maness Winter 2014 Cal Poly, Team 10-35, Maness Winter 2014 üyesi

CPSU-MANESS-W14S10G35

4 Üyeler

5 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 Gün: 9

Son 30 Gün: 57

Her zaman: 2,409