Giriş

When replacing the auto-away sensor, battery removal is necessary. The battery replacement guide should be a prerequisite before starting. The tools required are tweezers and a Phillips #0 screwdriver.

Parçalar

Hiçbir parçaya gerek yok.

  1. Grasp the display's metal outer ring with your fingers and pull directly away from the wall. Grasp the display's metal outer ring with your fingers and pull directly away from the wall.
    • Grasp the display's metal outer ring with your fingers and pull directly away from the wall.

  2. Turn the display over.
    • Turn the display over.

    • Remove the four 6 mm screws from the back of the display using a #0 Phillips screwdriver.

  3. Pinch the grey 20-pin connector with your fingers and pull directly away from the display. Do NOT pull too far as there is a ribbon on the back panel connecting the 20-pin connector to the display.
    • Pinch the grey 20-pin connector with your fingers and pull directly away from the display.

    • Do NOT pull too far as there is a ribbon on the back panel connecting the 20-pin connector to the display.

  4. Locate the blue pull tab at the end of the ribbon which says, "1. Pull". Grasp the tab with your fingers and pull directly away from the motherboard. Grasp the tab with your fingers and pull directly away from the motherboard.
    • Locate the blue pull tab at the end of the ribbon which says, "1. Pull".

    • Grasp the tab with your fingers and pull directly away from the motherboard.

  5. Pro Tech Toolkit içeren veya $100tüm siparişlerde ücretsiz kargo!

    Mağazamıza Göz Atın
  6. Locate the blue tab which says, "2. Pull". Use tweezers to pull the battery up and away from the display.
    • Locate the blue tab which says, "2. Pull".

    • Use tweezers to pull the battery up and away from the display.

    • Do NOT pull too far, as the battery is still connected to the motherboard and must be unplugged.

  7. Locate the blue tab which says "3 unplug". Grasp the battery with your fingers. Pull gently directly away from the display to unplug the battery from the motherboard.
    • Locate the blue tab which says "3 unplug".

    • Grasp the battery with your fingers. Pull gently directly away from the display to unplug the battery from the motherboard.

  8. Grasp the battery with your fingers and pull directly away from motherboard to separate the battery from the display. Grasp the battery with your fingers and pull directly away from motherboard to separate the battery from the display. Grasp the battery with your fingers and pull directly away from motherboard to separate the battery from the display.
    • Grasp the battery with your fingers and pull directly away from motherboard to separate the battery from the display.

  9. Locate the auto-away sensor.
    • Locate the auto-away sensor.

  10. Remove the four 3mm screws with a #0 Phillips screwdriver. Remove the one 4mm screw located at the edge of the auto-away sensor. Use a #0 Phillips screwdriver.
    • Remove the four 3mm screws with a #0 Phillips screwdriver.

    • Remove the one 4mm screw located at the edge of the auto-away sensor. Use a #0 Phillips screwdriver.

  11. Lift the auto-away sensor from motherboard using tweezers. Peel the copper foil gently from the EMI shield. Peel the copper foil gently from the EMI shield.
    • Lift the auto-away sensor from motherboard using tweezers.

    • Peel the copper foil gently from the EMI shield.

Sonuç

To reassemble your device, follow these instructions in reverse order.

2 farklı kişi bu kılavuzu tamamladı.

Justin Curry

Üyelik tarihi: 23-09-2014

252 İtibar

2 adet Kılavuz yazıldı

Takım

USF Tampa, Team 11-5, Blackwell Fall 2014 USF Tampa, Team 11-5, Blackwell Fall 2014 üyesi

USFT-BLACKWELL-F14S11G5

5 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 2

Son 30 Gün: 8

Her zaman: 1,456