Eşyalarını Tamir Et Topluluk Mağaza

Netgear Arlo Charging Port Replacement

Giriş

This is a step-by-step guide on how to remove the charging port in a Netgear Arlo

Neye ihtiyacın var

  1. Netgear Arlo Charging Port Replacement, Plastic Housing: adım 1, 1 resimden 1.

    • Remove the 2 (3.5mm) housing screws with a J0 screwdriver.

    Düzenle

  2. Netgear Arlo Charging Port Replacement: adım 2, 2 resimden 1. Netgear Arlo Charging Port Replacement: adım 2, 2 resimden 2.

    • Slide the unlocked battery cover forward to remove 2 (3.5mm) screws, that are behind the cover.

    Düzenle

  3. Netgear Arlo Charging Port Replacement: adım 3, 1 resimden 1.

    • Open the battery cover and remove the 2 (3.5mm") screws from under the cover.

    Düzenle

  4. Netgear Arlo Charging Port Replacement: adım 4, 3 resimden 1. Netgear Arlo Charging Port Replacement: adım 4, 3 resimden 2. Netgear Arlo Charging Port Replacement: adım 4, 3 resimden 3.

    • Use a plastic opening tool to start separating the plastic housing from the front side of the battery cover.

    • Next, start separating the plastic cover from the rear of the plastic housing, and work your way down the seam line.

    • Make sure the plastics snaps on the front of the plastic get unhooked from the grey plastic ring around the front of the camera.

    Düzenle

  5. Netgear Arlo Charging Port Replacement: adım 5, 3 resimden 1. Netgear Arlo Charging Port Replacement: adım 5, 3 resimden 2. Netgear Arlo Charging Port Replacement: adım 5, 3 resimden 3.

    • Remove the screw (3.5mm) near the sync button holding the opposite side of the camera on.

    • Remove the second screw (3.5mm) on the back of the camera to remove the second housing.

    • Once the screws are removed use an opening tool to pry back the second plastic mount.

    Düzenle

  7. Netgear Arlo Charging Port Replacement, Lens Assembly: adım 6, 1 resimden 1.

    • Remove 4 (6mm) large screws with a J00 screwdriver.

    • There are 2 on each side. This will allow you to remove the clear housing from the white housing.

    Düzenle

  8. Netgear Arlo Charging Port Replacement: adım 7, 2 resimden 1. Netgear Arlo Charging Port Replacement: adım 7, 2 resimden 2.

    • Once screws are removed, pull apart the clear housing.

    • Remove rod from camera cover.

    Düzenle

  9. Netgear Arlo Charging Port Replacement: adım 8, 3 resimden 1. Netgear Arlo Charging Port Replacement: adım 8, 3 resimden 2. Netgear Arlo Charging Port Replacement: adım 8, 3 resimden 3.

    • Remove Large ribbon cable first to disconnect front of camera from main body.

    • Remove 4 (3.5mm) small black screws from motherboard of the camera unit.

    • Remove smaller ribbon cable from underneath yellow tape.

    Düzenle

  10. Netgear Arlo Charging Port Replacement: adım 9, 1 resimden 1.

    • Once all ribbon cables are removed, remove the motherboard and camera assembly by pulling up on the black camera motherboard.

    Düzenle

  11. Netgear Arlo Charging Port Replacement, Charging Port: adım 10, 1 resimden 1.

    • Remove the 2 (.135") housing screws with a JIS00 screwdriver

    Düzenle

  12. Netgear Arlo Charging Port Replacement: adım 11, 1 resimden 1.

    • Remove 4 (.135") screws on the inside of the battery compartment using the JIS 00 screwdriver.

    Düzenle

  13. Netgear Arlo Charging Port Replacement: adım 12, 1 resimden 1.

    • Slide the two halves apart

    Düzenle

  14. Netgear Arlo Charging Port Replacement: adım 13, 1 resimden 1.

    • Remove the 2 (.135") screws holding the charging port on using the JIS 00 screwdriver.

    Düzenle

  15. Netgear Arlo Charging Port Replacement: adım 14, 2 resimden 1. Netgear Arlo Charging Port Replacement: adım 14, 2 resimden 2.

    • Remove the ribbon by prying the black ribbon holder up using the opening tool.

    • Pull the ribbon away from the charging port.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

2 farklı kişi bu kılavuzu tamamladı.

Yazar

1 tane daha katılımcı ile

Brian Johnson

Üyelik tarihi: 03/21/18

187 İtibar

1 Kılavuz yazıldı

Rozetler: 5

+2 tane daha rozet

Ekip

IUPUI, Team S2-G1, Freund Spring 2018 IUPUI, Team S2-G1, Freund Spring 2018 üyesi

IUPUI-FREUND-S18S2G1

2 Üyeler

4 adet Kılavuz yazıldı

4 Yorum

Great Job, Thank you!

Bob Olive Sr - Yanıt

Great thanks where did you get the replacement cable please thanks Mike

mikewalters1951 - Yanıt

where did you get the replacement cable please thanks  BOB

robertwatkins61 - Yanıt

Any hints on where the new port came from? I have the baby monitor and the port is cheap rubbish and needs replacing. Thanks

David - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 8

Son 30 gün: 56

Her zaman: 5,185