Ana içeriğe geç

Giriş

This guide will demonstrate how to remove the mother board from your camera.

  1. Electric shock is a huge risk if the battery is not removed while taking the camera apart. Press down and forward on the battery cover latch.
    • Electric shock is a huge risk if the battery is not removed while taking the camera apart.

    • Press down and forward on the battery cover latch.

    • Push the orange latch, in the direction of the arrow on it, to release the battery.

  2. Remove all the marked screws using a PH00 screwdriver. Remove the two 3mm screws on the grip. Remove the two 4mm screws on the side opposite the grip.
    • Remove all the marked screws using a PH00 screwdriver.

    • Remove the two 3mm screws on the grip.

    • Remove the two 4mm screws on the side opposite the grip.

    • Remove the three 4mm screws on the base of the camera.

    • Remove the four 3mm screws on the base of the camera.

  3. Open the flash module of the camera. Remove the 2mm screw from the microphone metal grid using a PH00 screwdriver.
    • Open the flash module of the camera.

    • Remove the 2mm screw from the microphone metal grid using a PH00 screwdriver.

    • Remove the 4mm screw that was under the metal microphone grid using a PH00 screwdriver.

  4. Separate the two parts of the body of the camera slightly. Release the two cables by lifting up their respective clips with a spudger.
    • Separate the two parts of the body of the camera slightly.

    • Release the two cables by lifting up their respective clips with a spudger.

    • Make sure not to pull too hard because there are connector ribbons.

    • Detach the connector ribbons before fully separating the camera into two pieces.

    • These pictures were taken after the connector ribbons were released and the camera was separated into two parts. You will need to release the connector ribbons while the camera is still in one piece before you can separate it like the pictures.

  5. iPhone Pil Tamir Setleri

    Only $29.99

    Buy Now

    iPhone Pil Tamir Setleri

    Only $29.99

    Buy Now
  6. Use a spudger to flip up the cable lock in order to release the ribbon.
    • Use a spudger to flip up the cable lock in order to release the ribbon.

  7. Use a PH00 screwdriver to unscrew the four labeled 3mm metal screws on the metal backing. Remove the four labeled 4mm screws connected to the motherboard.
    • Use a PH00 screwdriver to unscrew the four labeled 3mm metal screws on the metal backing.

    • Remove the four labeled 4mm screws connected to the motherboard.

    • Remove the metal support.

  8. Desolder the labeled soldering points. Soldering irons are very hot. They can damage your device and inflict physical harm if proper care is not taken.
    • Desolder the labeled soldering points.

    • Soldering irons are very hot. They can damage your device and inflict physical harm if proper care is not taken.

  9. Desolder the labeled soldering points. Desolder the labeled soldering points.
    • Desolder the labeled soldering points.

  10. Use a spudger to unlock the labeled connector ribbons. Disconnect the labeled connector ribbons. Disconnect the labeled connector ribbons.
    • Use a spudger to unlock the labeled connector ribbons.

    • Disconnect the labeled connector ribbons.

  11. Use a spudger to unlock the two connector ribbons. Disconnect the two connector ribbons.
    • Use a spudger to unlock the two connector ribbons.

    • Disconnect the two connector ribbons.

  12. Remove the mother board from the camera.
    • Remove the mother board from the camera.

Sonuç

To reassemble your device, follow these instructions in reverse order.

2 farklı kişi bu kılavuzu tamamladı.

Carmen Dang

Üyelik tarihi: 28-01-2015

358 İtibar

3 adet Kılavuz yazıldı

Takım

Cal Poly, Team 19-10, Maness Winter 2015 Cal Poly, Team 19-10, Maness Winter 2015 üyesi

CPSU-MANESS-W15S19G10

4 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 2

Son 7 Gün: 7

Son 30 Gün: 22

Her zaman: 3,362