Eşyalarını Tamir Et

Onarma Hakkı

Parçalar ve Aletler

Nintendo 64 Motherboard Replacement

Öne Çıkarılan

Yazan: tonymag28 (ve 11 başka katılımcı)
  • Yorumlar: 3
  • Favoriler: 40
  • Tamamlanma: 26

Öne Çıkan Kılavuzlar

Zorluk

Kolay

Adımlar

16

Gerekli Süre

15 - 20 dakika

Bölümler

3

İşaretler

1

Featured Guide

Öne Çıkan Kılavuzlar

Bu kılavuz, iFixit kadrosu tarafından acayip havalı bulundu.

Giriş

This guide will show how to replace the Nintendo 64 motherboard.

  1. Remove the expansion pack cover by pushing in the tab and pulling out.

    • Remove the expansion pack cover by pushing in the tab and pulling out.

    Düzenle

  2. If your system uses a jumper pack, the same procedure applies to remove it.

    • If your system uses a jumper pack, the same procedure applies to remove it.

    • A small spoon can be used in place of a spudger.

    • Lever the expansion pack out using a metal spudger.

    Düzenle

  3. Remove the six screws on the bottom side indicated in the example with a gamebit head or screwdriver.

    • Remove the six screws on the bottom side indicated in the example with a gamebit head or screwdriver.

    Düzenle

  4. Remove the two front feet of the N64.

    • Remove the two front feet of the N64.

    Düzenle

  5. Rotate to top side up and lift off top cover.

    • Rotate to top side up and lift off top cover.

    Düzenle

  6. Remove the fourteen screws indicated in the example using the larger Phillips screwdriver. Remove the fourteen screws indicated in the example using the larger Phillips screwdriver.

    • Remove the fourteen screws indicated in the example using the larger Phillips screwdriver.

    Düzenle

  7. Nintendo Switch Setleri

    A quick fix to get back in the game

    Shop Switch Kits

    Nintendo Switch Setleri

    A quick fix to get back in the game

    Shop Switch Kits

  8. Remove the metal plate indicated in the example by sliding it back and then lifting it up. Remove the metal plate indicated in the example by sliding it back and then lifting it up.

    • Remove the metal plate indicated in the example by sliding it back and then lifting it up.

    Düzenle

  9. Remove the two screws indicated in the example using the smaller Phillips screwdriver.

    • Remove the two screws indicated in the example using the smaller Phillips screwdriver.

    Düzenle

  10. Remove the screw to the right of the LED light using the larger Phillips screwdriver.

    • Remove the screw to the right of the LED light using the larger Phillips screwdriver.

    Düzenle

  11. Remove the small metal bracket from the back of the expansion pack slot.

    • Remove the small metal bracket from the back of the expansion pack slot.

    Düzenle

  12. Remove the small metal bracket from the front of the expansion pack slot with the metal spudger. Remove the small metal bracket from the front of the expansion pack slot with the metal spudger.

    • Remove the small metal bracket from the front of the expansion pack slot with the metal spudger.

    Düzenle

  13. Remove the small metal bracket behind the expansion slot using the spudger. Remove the small metal bracket behind the expansion slot using the spudger.

    • Remove the small metal bracket behind the expansion slot using the spudger.

    Düzenle

  14. Remove the seven screws indicated in the example using the larger Phillips screwdriver. Remove the seven screws indicated in the example using the larger Phillips screwdriver.

    • Remove the seven screws indicated in the example using the larger Phillips screwdriver.

    Düzenle

  15. Lift off and remove the metal plate as indicated in the example.

    • Lift off and remove the metal plate as indicated in the example.

    Düzenle

  16. Remove the four screws indicated using the #1 Phillips screwdriver.

    • Remove the four screws indicated using the #1 Phillips screwdriver.

    Düzenle

  17. Lift up and remove the motherboard.

    • Lift up and remove the motherboard.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

26 farklı kişi bu kılavuzu tamamladı.

Yazar

11 tane daha katılımcı ile

tonymag28

Üyelik tarihi: 28-10-2009

1.774 İtibar

3 adet Kılavuz yazıldı

Rozetler: 13

+10 tane daha rozet

Takım

Cal Poly, Team 5-4, Regan Fall 2009 Cal Poly, Team 5-4, Regan Fall 2009 üyesi

CPSU-REGAN-F09S5G4

7 Üyeler

6 adet Kılavuz yazıldı

Bir Yorum

Yorum Ekle

4.2mm doesn't seem right. When I looked to purchase all I saw was 4.5mm and now that I have one in my hand it seems to fit very precisely on the screws on my N64.

negroslim - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 5

Son 7 gün: 47

Son 30 gün: 225

Her zaman: 48,839