Giriş

The removal of the main logic board of the DS is essential to access the screens and to replace other components.

Remove the cartridge from the console. Use a Phillips #00 Screwdriver to remove the screw securing the battery door to the rear case, turning the screw counter-clockwise. Remove the battery door.
  • Remove the cartridge from the console.

  • Use a Phillips #00 Screwdriver to remove the screw securing the battery door to the rear case, turning the screw counter-clockwise.

  • Remove the battery door.

Yorum Ekle

Use a plastic opening tool or spudger to pry out the battery from the bottom. If a plastic open tool or spudger isn't available, your fingernails may work.
  • Use a plastic opening tool or spudger to pry out the battery from the bottom. If a plastic open tool or spudger isn't available, your fingernails may work.

Yorum Ekle

Remove the battery from the Nintendo DS.
  • Remove the battery from the Nintendo DS.

Yorum Ekle

Remove the 7 Y0 screws located on the back.
  • Remove the 7 Y0 screws located on the back.

  • It might be helpful to remove the strap from the hole to access the top left screw.

Yorum Ekle

MANTA DRIVER KIT
112 bit driver kit $59.99
MANTA DRIVER KIT
112 bit driver kit $59.99
With your hands, pry the back panel off the main case. Separate the back from the front, and set it aside. Separate the back from the front, and set it aside.
  • With your hands, pry the back panel off the main case.

  • Separate the back from the front, and set it aside.

Yorum Ekle

Using a Phillips #00 screwdriver, remove the 4 screws on the circuit board.
  • Using a Phillips #00 screwdriver, remove the 4 screws on the circuit board.

  • Be careful NOT to slip with the screwdriver, you can damage the circuit board!

Yorum Ekle

Unlock the two large ribbon cables by moving the black clip up. Carefully pull the ribbon cables down and out with your fingers. Do not use pliers to pull the cables, as they can be damaged easily.
  • Unlock the two large ribbon cables by moving the black clip up.

  • Carefully pull the ribbon cables down and out with your fingers.

  • Do not use pliers to pull the cables, as they can be damaged easily.

Yorum Ekle

Locate the two small ribbon cables, beneath the rightmost large ribbon cable. Slide the locks for the small ribbon cables down to the side, and remove the cables.
  • Locate the two small ribbon cables, beneath the rightmost large ribbon cable.

  • Slide the locks for the small ribbon cables down to the side, and remove the cables.

  • It may be useful to use tweezers to remove the small ribbon cables.

  • Be careful not to damage the delicate ribbon cables.

Yorum Ekle

Locate the Wifi antenna pigtail connector Remove the antenna by grasping it at the head with tweezers. Using a slight rocking motion, pull up to dislodge the connector.
  • Locate the Wifi antenna pigtail connector

  • Remove the antenna by grasping it at the head with tweezers. Using a slight rocking motion, pull up to dislodge the connector.

Yorum Ekle

Feed the ribbon cables through the opening on the board.
  • Feed the ribbon cables through the opening on the board.

  • Pull up and remove the circuit board, and set it aside.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

7 başka kişi bu kılavuzu tamamladı.

kingdesmond

Üyelik tarihi: 27-10-2009

1.305 İtibar

2 adet Kılavuz yazıldı

Takım

Cal Poly, Team 18-3, Maness Fall 2009 Cal Poly, Team 18-3, Maness Fall 2009 üyesi

CPSU-MANESS-F09S18G3

4 Üye

10 adet Kılavuz yazıldı

Bir Yorum

This was really helpful. Thank you!

Jess Anderson - Yanıtla

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 2

Son 7 Gün: 15

Son 30 Gün: 89

Tüm Zamanlar: 18,725