Giriş

This guide will help you remove the circuit board from the outer telephone case. You may need to remove the circuit board to repair internal components, such as buttons.

Flip the phone over to view the back. Remove the power and phone cords. Remove the power and phone cords.
  • Flip the phone over to view the back.

  • Remove the power and phone cords.

Yorum Ekle

Remove the seven 8mm Phillips #2 screws.
  • Remove the seven 8mm Phillips #2 screws.

Yorum Ekle

Lift up the back cover slowly because there are still wires attached to the circuit board. Lifting the back cover should not require a lot of force; simply lift with your fingertips.
  • Lift up the back cover slowly because there are still wires attached to the circuit board.

  • Lifting the back cover should not require a lot of force; simply lift with your fingertips.

Yorum Ekle

Disconnect the rubber piece by pulling it out of the slot, freeing the back cover completely.
  • Disconnect the rubber piece by pulling it out of the slot, freeing the back cover completely.

Yorum Ekle

Remove the six 8mm Phillips #2 screws. Pull the speaker phone cover straight up.
  • Remove the six 8mm Phillips #2 screws.

  • Pull the speaker phone cover straight up.

Yorum Ekle

Remove the red and white wires from the rubber casing rim.
  • Remove the red and white wires from the rubber casing rim.

Yorum Ekle

Lift out the speaker and set it away from the tray that holds it. Then remove the black plastic tray at the bottom by lifting it straight up.
  • Lift out the speaker and set it away from the tray that holds it.

  • Then remove the black plastic tray at the bottom by lifting it straight up.

Yorum Ekle

Remove the two 8mm Phillips #2 screws.
  • Remove the two 8mm Phillips #2 screws.

Yorum Ekle

Pull the gray plastic casing away from the circuit board as you remove the clear, curved, plastic piece straight up. Pull the gray plastic casing away from the circuit board as you remove the clear, curved, plastic piece straight up.
  • Pull the gray plastic casing away from the circuit board as you remove the clear, curved, plastic piece straight up.

Yorum Ekle

There are three clips on the circuit board to un-clip. Unclip both back black clips with your fingertips. Push the middle black clip towards the bottom of the picture with a flathead screwdriver.
  • There are three clips on the circuit board to un-clip.

  • Unclip both back black clips with your fingertips.

  • Push the middle black clip towards the bottom of the picture with a flathead screwdriver.

Yorum Ekle

There's a brown ribbon still attached to the circuit board and phone case, so don't pull the circuit board completely off just yet. Lift the edge of the circuit board over the phone case and slightly up, so the bottom of circuit board can be viewed.
  • There's a brown ribbon still attached to the circuit board and phone case, so don't pull the circuit board completely off just yet.

  • Lift the edge of the circuit board over the phone case and slightly up, so the bottom of circuit board can be viewed.

Yorum Ekle

Push down each brown clip on either side of the brown metal strip using your fingertip.
  • Push down each brown clip on either side of the brown metal strip using your fingertip.

  • Detach the circuit board from the brown ribbon.

Yorum Ekle

Remove the clear rubber casing.
  • Remove the clear rubber casing.

  • Be careful not to flip over the front phone casing or all of the buttons will fall out.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

2 başka kişi bu kılavuzu tamamladı.

Elizabeth

Üyelik tarihi: 21-01-2012

160 İtibar

3 adet Kılavuz yazıldı

Takım

Cal Poly, Team 10-35, Amido Winter 2012 Cal Poly, Team 10-35, Amido Winter 2012 üyesi

CPSU-AMIDO-W12S10G35

4 Üyeler

5 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 6

Son 30 Gün: 13

Her zaman: 1,657