Eşyalarını Tamir Et Topluluk Mağaza

Numark N4 Effect button cover Replacement

Giriş

This guide shows the reader how to replace the effect button cover. If this plastic part is damaged and doesn't touch the circuit board when pressure is applied, it is likely responsible for an unresponsive effects button.

Neye ihtiyacın var

  1. Numark N4 Effect button cover Replacement, Numark N4 Disassembly: adım 1, 1 resimden 1.

    • Turn the Numark N4 over so that the bottom panel is facing upwards.

    • Loosen and remove the 17 12mm screws from the bottom panel using a Phillips #2 screwdriver.

    Düzenle

  2. Numark N4 Effect button cover Replacement: adım 2, 1 resimden 1.

    • Using your fingers, gently pull apart the two panels of the device until you feel resistance from the cables.

    Düzenle

  3. Numark N4 Effect button cover Replacement: adım 3, 1 resimden 1.

    • Using your fingers, gently unplug the larger ribbon cable as pictured.

    Düzenle

  4. Numark N4 Effect button cover Replacement: adım 4, 1 resimden 1.

    • Using your fingers, gently unplug the smaller ribbon cable as pictured.

    Düzenle

  6. Numark N4 Effect button cover Replacement: adım 5, 1 resimden 1.

    • Using your fingers, gently unplug the yellow and red cable as pictured.

    Düzenle

  7. Numark N4 Effect button cover Replacement: adım 6, 1 resimden 1.

    • Open the two panels completely, gently placing each side on your working area to avoid damage to the buttons on the outside face.

    Düzenle

  8. Numark N4 Effect button cover Replacement, Effect button cover: adım 7, 1 resimden 1.

    • Locate the top right PCB circuit board.

    Düzenle

  9. Numark N4 Effect button cover Replacement: adım 8, 1 resimden 1.

    • Unplug the two ribbon cables as shown.

    Düzenle

  10. Numark N4 Effect button cover Replacement: adım 9, 1 resimden 1.

    • Loosen and remove the 11 12mm screws from the circuit board using Phillips #2 screwdriver.

    Düzenle

  11. Numark N4 Effect button cover Replacement: adım 10, 1 resimden 1.

    • Carefully remove the circuit board from its housing.

    Düzenle

  12. Numark N4 Effect button cover Replacement: adım 11, 1 resimden 1.

    • Carefully remove the plastic button covers as depicted.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

2 farklı kişi bu kılavuzu tamamladı.

Yazar

1 tane daha katılımcı ile

Erik Charlton

Üyelik tarihi: 10/10/17

789 İtibar

5 adet Kılavuz yazıldı

Rozetler: 14

+11 tane daha rozet

Ekip

USF Tampa, Team S13-G11, Cagle Fall 2017 USF Tampa, Team S13-G11, Cagle Fall 2017 üyesi

USFT-CAGLE-F17S13G11

4 Üyeler

12 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 3

Son 30 gün: 11

Her zaman: 467