Giriş

This guide shows how to replace the camera lens and surrounding mechanisms (including the motor).

Parçalar

Hiçbir parçaya gerek yok.

  1. Flip camera so you are looking at the bottom.
    • Flip camera so you are looking at the bottom.

    • Unscrew all 5 base plate screws.

    Yorum Ekle

  2. Lift open retainer clip by sliding the clip to the left and letting the clip pop up.
    • Lift open retainer clip by sliding the clip to the left and letting the clip pop up.

    Yorum Ekle

    • Unscrew the single screw located next to the battery slot.

    Yorum Ekle

    • Turn the camera so that the USB, AV and DC in/out rubber plate it facing you.

    • Lift the rubber plate exposing the ports beneath.

    Yorum Ekle

    • Unscrew the 2 screws next to the USB and AC ports.

    Yorum Ekle

    • Use a flathead screwdriver or another flat opening tool to pry the faceplate from the whole device.

    Yorum Ekle

    • Pull off the faceplate to reveal the inside of the camera.

    • Be careful of the connector that goes from the faceplate to the motherboard . Disconnecting this line will cause the camera not not power on through the on/off switch anymore.

    Yorum Ekle

    • Use a phillips head screwdriver to remove the 3 screws highlighted in the picture.

    Yorum Ekle

    • Unscrew the 2 screws located on either side of the flash.

    Yorum Ekle

    • Get a flathead screwdriver or an iPod opening tool (both are shown in this picture).

    • Carefully pry off the blackplate from the remaining part of the camera.

    Yorum Ekle

    • Pull the backplate off.

    Yorum Ekle

    • Unscrew the screw shown in the picture from LCD screen.

    Yorum Ekle

    • Remove the side pannel by sliding it off the body of the camera.

    • Lift the camera no more than 3cm to make sure all screws have been taken off.

    Yorum Ekle

    • Flip camera so you are looking at the front.

    • Remove gray and blue wiring with tweasers by gently wiggling and pulling.

    • Be careful not to rip the wiring tape with the tweezers.

    Yorum Ekle

    • Locate the tape securing the wiring with the gray end piece located on top of the camera.

    • Gently lift up on the tape till all wires are exposed.

    Yorum Ekle

    • Flip Camera to the bottom side as shown.

    • Pull and wriggle the thin yellow wiring tape to detach it from the rest of the camera, while leaving it attached to the LCD screen.

    Yorum Ekle

    • Flip camera so the front is facing you.

    • Locate speaker in upper right hand corner.

    • Gently lift with tweasers.

    • Feed wiring through designated spot so that it is no longer connected to the camera.

    Yorum Ekle

    • Lift the LCD screen so the thick yellow wiring is the only thing attaching the LCD screen to the camera.

    • Gently pull the thick yellow wiring out by using the forefinger and thumb.

    Yorum Ekle

    • Flip camera so you are looking at the back.

    • Remove the 3 screws from the rear of the camera behind the lens.

    Yorum Ekle

    • Flip camera so the front lens is facing up.

    • Unplug lens from logic board.

    Yorum Ekle

    • Flip camera over so the lens is facing down and the back of the camera is facing you.

    • Gently pull back on the wire that connects logic board to lens assembly so it is no longer connected.

    Yorum Ekle

    • Flip camera so the front is facing you.

    • Carefully lift lens assembly out of camera.

    Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

Joshua

Üyelik tarihi: 15-04-2010

7 İtibar

2 adet Kılavuz yazıldı

Takım

Cal Poly, Team 28-23, Regan Spring 2010 Cal Poly, Team 28-23, Regan Spring 2010 üyesi

CPSU-REGAN-S10S28G23

4 Üyeler

7 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 0

Son 30 Gün: 2

Her zaman: 2,350