Eşyalarını Tamir Et Topluluk Mağaza

Osmo Mobile Trigger Button Replacement

Giriş

The trigger button is the one of the most used buttons on the DJI Osmo Mobile, and this guide will serve to teach the device owner how to replace a broken or unresponsive trigger button.

Neye ihtiyacın var

  1. Osmo Mobile Trigger Button Replacement, Osmo Mobile Handle Disassembly: adım 1, 2 resimden 1. Osmo Mobile Trigger Button Replacement, Osmo Mobile Handle Disassembly: adım 1, 2 resimden 2.

    • Remove gimbal from base handle by loosening round plate found at the top of the handle.

    Düzenle

  2. Osmo Mobile Trigger Button Replacement: adım 2, 2 resimden 1. Osmo Mobile Trigger Button Replacement: adım 2, 2 resimden 2.

    • Use Phillips #00 screwdriver to remove the three screws found on the gimbal stabilizer to detach handle from gimbal.

    • Carefully detach handle from gimbal and disconnect the cable that connects the two.

    Düzenle

  3. Osmo Mobile Trigger Button Replacement: adım 3, 1 resimden 1.

    • Locate the hex screws found at the top base of the handle, and unscrew using the 1.5mm hex screwdriver.

    Düzenle

  4. Osmo Mobile Trigger Button Replacement: adım 4, 2 resimden 1. Osmo Mobile Trigger Button Replacement: adım 4, 2 resimden 2.

    • Remove joystick by gently pulling away from handle

    Düzenle

  6. Osmo Mobile Trigger Button Replacement: adım 5, 3 resimden 1. Osmo Mobile Trigger Button Replacement: adım 5, 3 resimden 2. Osmo Mobile Trigger Button Replacement: adım 5, 3 resimden 3.
    Bu adımda kullanılan alet:
    Tweezers
    $4.99
    Satın Al

    • Remove the quick release PCBA by locating the connecting wires and release the ribbon cable with tweezers.

    • Use the spudger to pry open and remove the face plate, starting at the back of the handle.

    Düzenle

  7. Osmo Mobile Trigger Button Replacement: adım 6, 3 resimden 1. Osmo Mobile Trigger Button Replacement: adım 6, 3 resimden 2. Osmo Mobile Trigger Button Replacement: adım 6, 3 resimden 3.

    • Locate four screws directly on top of handle.

    • Unscrew the silver, bottom two screws, that are closest to the face plate using the 00 screwdriver.

    • Unscrew the black, top two screws, located furthest from the face plate, using the 0 screwdriver.

    • Remove the remaining two screws found on the front of the faceplate.

    • Remove the rest of the face plate shell.

    Düzenle

  8. Osmo Mobile Trigger Button Replacement, Charging Port: adım 7, 1 resimden 1.

    • Remove the top left screw on the joystick panel with Phillips #00 screwdriver.

    • Lift faceplate holding joystick module.

    Düzenle

  9. Osmo Mobile Trigger Button Replacement: adım 8, 1 resimden 1.

    • Remove the bottom right screw on the joystick panel with the #00 Phillips screwdriver.

    Düzenle

  10. Osmo Mobile Trigger Button Replacement: adım 9, 1 resimden 1.

    • Hold down the larger of the two ribbon cables, and pull on circuit board with a constant and careful down and out motion.

    Düzenle

  11. Osmo Mobile Trigger Button Replacement: adım 10, 1 resimden 1.

    • Remove the two screws from the green charging module and the two screws on the grey plate and remove from handle.

    • Replace charging module.

    Düzenle

  12. Osmo Mobile Trigger Button Replacement, Trigger Button: adım 11, 2 resimden 1. Osmo Mobile Trigger Button Replacement, Trigger Button: adım 11, 2 resimden 2.
    Bu adımda kullanılan alet:
    Tweezers
    $4.99
    Satın Al

    • Use the tweezers to push outward on the backside of the trigger button hinges.

    • Pop out trigger button.

    Düzenle

  13. Osmo Mobile Trigger Button Replacement: adım 12, 1 resimden 1.

    • Use the tweezers to remove the underlying button that contacts with the trigger button, and replace.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

4 tane daha katılımcı ile

William Tyler Wills

Üyelik tarihi: 09/28/17

429 İtibar

4 adet Kılavuz yazıldı

Rozetler: 10

+7 tane daha rozet

Ekip

USF Tampa, Team S2-G1, Nance Fall 2017 USF Tampa, Team S2-G1, Nance Fall 2017 üyesi

USFT-NANCE-F17S2G1

4 Üyeler

12 adet Kılavuz yazıldı

1Rehber Yorum

How I can fix the USB port, it went inside the handle?

Juan Carlos Beltran - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 6

Son 30 gün: 43

Her zaman: 2,690