Eşyalarını Tamir Et

Onarma Hakkı

Parçalar ve Aletler

Palm Treo 650 Speaker Replacement

Yazan: cgood (ve 5 başka katılımcı)
  • Yorumlar: 0
  • Favoriler: 1

Zorluk

Kolay

Adımlar

7

Gerekli Süre

2 dakika

Bölümler

3

İşaretler

3

Grammar Police

Gramer Polisi

İçinizdeki Türkçe öğretmenini ortaya çıkarın ve bu kılavuzun yazımının geliştirilmesine yardımcı olun!

Inconsistent Images

Tutarsız Görseller

Bu kılavuzdaki görselleri ön koşullarla daha tutarlı olacak şekilde güncellemek, kusursuzluğunuza katkıda bulunacaktır.

Incorrect Tools

Yanlış Araçlar

Resimlerde ve/veya metinde doğru araçları kullanarak bu kılavuzun daha iyi hale gelmesine yardımcı olun.

Giriş

This guide will show how to remove and replace the speaker from the phone shell.

  1. Position the phone so the screen faces down.

    • Position the phone so the screen faces down.

    • Remove the stylus found on the back of the phone.

    Düzenle

  2. To remove the battery cover, hold down the button in the middle of the phone's back.

    • To remove the battery cover, hold down the button in the middle of the phone's back.

    • Slide the cover down to remove. Set the cover aside.

    Düzenle

  3. Lift the edge of the battery, separating contact points, and pull out as pictured. Lift the edge of the battery, separating contact points, and pull out as pictured.

    • Lift the edge of the battery, separating contact points, and pull out as pictured.

    Düzenle

  4. Manta Tornavida Seti

    112 bits for every fix.

    Upgrade Your Toolbox

    Manta Tornavida Seti

    Upgrade Your Toolbox

  5. Remove the small round rubber cover on the back of the phone located immediately below the antenna.

    • Remove the small round rubber cover on the back of the phone located immediately below the antenna.

    • This will uncover a screw that will be removed in the next step.

    Düzenle

  6. Unscrew six black 6.9 mm Torx screws with a T5 Torx Screwdriver. Unscrew one 9.75 mm Phillips antenna screw with a Phillips #00 Screwdriver. Pull out the antenna.

    • Unscrew six black 6.9 mm Torx screws with a T5 Torx Screwdriver.

    • Unscrew one 9.75 mm Phillips antenna screw with a Phillips #00 Screwdriver.

    • Pull out the antenna.

    Düzenle

  7. Pry the back cover off using a spudger or similar tool. The back cover is attached by several small clips on the inside.

    • Pry the back cover off using a spudger or similar tool.

    • The back cover is attached by several small clips on the inside.

    Düzenle

  8. Using an ipod case opener or similar tool, simply pry off the speaker. This may be glued in, so remove carefully.

    • Using an ipod case opener or similar tool, simply pry off the speaker.

    • This may be glued in, so remove carefully.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

5 tane daha katılımcı ile

cgood

Üyelik tarihi: 28-10-2009

122 İtibar

7 adet Kılavuz yazıldı

Rozetler: 10

+7 tane daha rozet

Takım

Cal Poly, Team 19-3, Maness Fall 2009 Cal Poly, Team 19-3, Maness Fall 2009 üyesi

CPSU-MANESS-F09S19G3

4 Üyeler

18 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 1

Her zaman: 2,299