Giriş

This guide will take you through the steps of how to replace the flash assembly.

Parçalar

Hiçbir parçaya gerek yok.

Move the switch on the battery door to the Open position.
  • Move the switch on the battery door to the Open position.

  • The door will automatically swing open after you let it go.

Yorum Ekle

Push the small gray tab on the top right corner to the left. The battery will pop out slightly. Keep your finger clear of the battery when it pops out.
  • Push the small gray tab on the top right corner to the left. The battery will pop out slightly.

  • Keep your finger clear of the battery when it pops out.

Yorum Ekle

Push the memory card in and let go.
  • Push the memory card in and let go.

  • The memory card will pop out slightly.

  • Pull out the memory card.

Yorum Ekle

Unscrew the small screws on the sides of the camera. The screws on the left side(#00P, 4.7mm) are longer than the screw on the right side(#00P, 3.3mm).
  • Unscrew the small screws on the sides of the camera.

  • The screws on the left side(#00P, 4.7mm) are longer than the screw on the right side(#00P, 3.3mm).

Yorum Ekle

Unscrew the three small screws on the bottom(#00P, 3.3mm). The bottom will fall off.
  • Unscrew the three small screws on the bottom(#00P, 3.3mm).

  • The bottom will fall off.

Yorum Ekle

Lift up the bottom back cover by prying the bottom edge with the spudger. Gently lift up the back cover with your hand from the bottom to the top. Gently lift up the back cover with your hand from the bottom to the top.
  • Lift up the bottom back cover by prying the bottom edge with the spudger.

  • Gently lift up the back cover with your hand from the bottom to the top.

Yorum Ekle

Lift the tabs on the ZIF connectors. The ribbon cables should easily come out of the ZIF connectors. The ribbon cables should easily come out of the ZIF connectors.
  • Lift the tabs on the ZIF connectors.

  • The ribbon cables should easily come out of the ZIF connectors.

Yorum Ekle

Using the spudger, pry off the top cover by gliding the spudger along the entire edge between the top cover and the front cover. Be careful not to damage the cylindrical capacitor on the circuit board under the top cover.
  • Using the spudger, pry off the top cover by gliding the spudger along the entire edge between the top cover and the front cover.

  • Be careful not to damage the cylindrical capacitor on the circuit board under the top cover.

Yorum Ekle

Unscrew the small screws beneath the top cover(#00P, 1.7mm).
  • Unscrew the small screws beneath the top cover(#00P, 1.7mm).

Yorum Ekle

Lift the logic board out with your hand by pushing the tabs out and pulling the logic board up. The on/off switch and the anti-shake button may fall out. The on/off switch and the anti-shake button may fall out.
  • Lift the logic board out with your hand by pushing the tabs out and pulling the logic board up.

  • The on/off switch and the anti-shake button may fall out.

Yorum Ekle

The flash assembly is hardwired into the top circuit board.
  • The flash assembly is hardwired into the top circuit board.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

Karissa

Üyelik tarihi: 13-04-2012

50 İtibar

8 adet Kılavuz yazıldı

Takım

Cal Poly, Team 6-23, Amido Spring 2012 Cal Poly, Team 6-23, Amido Spring 2012 üyesi

CPSU-AMIDO-S12S6G23

4 Üyeler

10 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 1

Son 30 Gün: 2

Tüm Zamanlar: 350