Ana içeriğe geç

Giriş

This step by step guide will help you replace a faulty top assembly without damage to any of the other components on the camera.

  1. Remove the battery and the SD card
    • Remove the battery and the SD card

  2. Remove the two bottom 1.0 mm screws with a Phillips #000 screwdriver Remove the two 1.0 mm screws to the left with a Phillips #000 screwdriver Remove the two 1.0 mm screws to the right with a Phillips #000 screwdriver
    • Remove the two bottom 1.0 mm screws with a Phillips #000 screwdriver

    • Remove the two 1.0 mm screws to the left with a Phillips #000 screwdriver

    • Remove the two 1.0 mm screws to the right with a Phillips #000 screwdriver

  3. Carefully separate the back of the camera from the main body
    • Carefully separate the back of the camera from the main body

    • Do not apply excessive force. The LCD is connected by ribbon cables that can be easily damaged

  4. Use the tip of the 2.0 mm flathead screwdriver to flip up the black tabs on the ribbon cables Pull gently on the ribbon cables to unseat them
    • Use the tip of the 2.0 mm flathead screwdriver to flip up the black tabs on the ribbon cables

    • Pull gently on the ribbon cables to unseat them

  5. MacBook Pil Tamir Setleri

    Başlangıç $69.99

    Buy Now

    MacBook Pil Tamir Setleri

    Başlangıç $69.99

    Buy Now
  6. Remove the two 1.0 mm screws to the right with a Phillips #000 screwdriver Remove the two 1.0 mm screws to the left with a Phillips #000 screwdriver Remove one 1.0 mm screw from the bottom with a Phillips #000 screwdriver
    • Remove the two 1.0 mm screws to the right with a Phillips #000 screwdriver

    • Remove the two 1.0 mm screws to the left with a Phillips #000 screwdriver

    • Remove one 1.0 mm screw from the bottom with a Phillips #000 screwdriver

  7. Carefully separate the front of the camera from the main body
    • Carefully separate the front of the camera from the main body

  8. Use the tip of the 1.5 mm flathead screwdriver to disengage the plastic tab Carefully lift the selector switch away from the motherboard
    • Use the tip of the 1.5 mm flathead screwdriver to disengage the plastic tab

    • Carefully lift the selector switch away from the motherboard

  9. Remove three 1.0 mm screws with a Phillips #000 screwdriver Use the tip of the 2.0 mm flathead screwdriver to disengage the metal tab, then carefully lift the shield away from the motherboard
    • Remove three 1.0 mm screws with a Phillips #000 screwdriver

    • Use the tip of the 2.0 mm flathead screwdriver to disengage the metal tab, then carefully lift the shield away from the motherboard

  10. Insert the tip of the 2.0 mm flathead into the center hole of the tripod mount, and apply force in the direction facing away from the button.
    • Insert the tip of the 2.0 mm flathead into the center hole of the tripod mount, and apply force in the direction facing away from the button.

    • Carefully lift the tripod mount out of the camera body

  11. Use the 2.0 mm flathead to flip up the brown tab on the motherboard and carefully unseat the ribbon cable Insert the tip of the 2.0 mm flathead screwdriver into the hole on the daughter board, then apply upward force to remove the daughter board from the main case
    • Use the 2.0 mm flathead to flip up the brown tab on the motherboard and carefully unseat the ribbon cable

    • Insert the tip of the 2.0 mm flathead screwdriver into the hole on the daughter board, then apply upward force to remove the daughter board from the main case

  12. Use the 2.0 mm flathead to flip up the two tabs on the motherboard and carefully unseat the ribbon cables Use the Phillips #000 screwdriver to remove the three silver screws Carefully lift the lens assembly out of the camera
    • Use the 2.0 mm flathead to flip up the two tabs on the motherboard and carefully unseat the ribbon cables

    • Use the Phillips #000 screwdriver to remove the three silver screws

    • Carefully lift the lens assembly out of the camera

  13. Use the tip of the 2.0 mm flathead screwdriver to disengage the tab on the back of the camera Use the tip of the 2.0 mm flathead screwdriver to disengage the two tabs on the front of the camera Carefully lift the top assembly out of place
    • Use the tip of the 2.0 mm flathead screwdriver to disengage the tab on the back of the camera

    • Use the tip of the 2.0 mm flathead screwdriver to disengage the two tabs on the front of the camera

    • Carefully lift the top assembly out of place

Sonuç

To reassemble your device, follow these instructions in reverse order.

Derrick Thompson

Üyelik tarihi: 30-01-2018

1.035 İtibar

5 adet Kılavuz yazıldı

Takım

Baylor, Team S2-G5, Johnson Spring 2018 Baylor, Team S2-G5, Johnson Spring 2018 üyesi

BU-JOHNSON-S18S2G5

3 Üyeler

5 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 2

Son 30 Gün: 2

Her zaman: 82